Dryer Not Heating: Gas and Electric Causes, Safe Checks and Fixes

A dryer that tumbles but stays cold usually has one of a short list of problems. On an electric dryer it's most often a tripped breaker, a blown thermal fuse, or a burned-out heating element. On a gas dryer it's the gas supply, the igniter, the flame sensor, or the gas valve coils. A clogged vent can make either type overheat and shut the heat off. Start with the checks below. They take about 15 minutes and need no tools.

First, which kind of "no heat" do you have?

The symptom narrows things down faster than anything else. Put a few damp towels in, run Timed Dry on high heat for 10 minutes, then open the door and feel the drum and the towels. Find the row that matches what you notice.

What you noticeElectric dryer: likely causeGas dryer: likely cause
Drum turns, no heat at allTripped breaker, thermal fuse, or heating elementClosed gas valve, igniter, flame sensor, thermal fuse
Heats for a few minutes, then goes coldThermostat, restricted ventGas valve coils, restricted vent
Warm, but clothes need two cyclesClogged vent or lint screen, big loads, 208-volt building supplyClogged vent or lint screen, big loads
Gets very hot, then shuts offBlocked ventBlocked vent
Burning smell or gas smellStop using it and callLeave the house, see the gas warning below

Safe checks to do before you call

None of these need tools or opening the cabinet. Unplug an electric dryer before you move it or touch the duct behind it. If yours is gas, slide it out gently so you don't pull on the flexible gas line.

1. Check the cycle setting

Air Fluff, Air Dry, and Wrinkle Care use little or no heat, and so do some delicate and eco settings. For the test, pick Timed Dry on High. On some models the temperature button can end up on "no heat" by accident.

2. Clean the lint screen

A packed screen chokes the airflow through the drum. Pull the lint off, and if the mesh looks coated from dryer sheets, wash it with warm water and a soft brush. Let it dry completely before you put it back.

3. Feel the air outside

With the dryer running, go outside to the vent hood and hold your hand in front of it. You should feel a strong, warm stream and see the flap open. If the air is weak or you feel nothing, lint or a crushed duct is blocking the path between the dryer and the wall.

4. Look at the duct behind the dryer

The short duct behind the dryer gets crushed easily when the dryer is pushed back against the wall. Look for kinks, flat spots, and lint packed at the joints. Plastic or thin foil duct should be swapped for metal duct.

5. Reset the breaker (electric dryers)

An electric dryer runs on 240 volts through a double breaker. The motor and controls run on half of that, while the heating element needs the full 240. So when one half trips, or a loose wire drops one side, the drum keeps turning and nothing heats. Turn the dryer breaker all the way off, wait a few seconds and turn it back on. In an older panel with fuses, check both fuses. If the breaker trips again, stop resetting it and call a technician.

6. Check the gas valve (gas dryers)

Find the shutoff valve on the gas line behind the dryer. When it's open, the handle points along the pipe. If it sits across the pipe, the valve is closed, so the drum spins but the burner has nothing to light. While you're at it, make sure the stove or water heater still has gas. If they don't, the problem is the gas supply, not the dryer.

7. Try a smaller load

A stuffed drum or dripping-wet clothes can feel like a heating problem. Fill the drum about three quarters full at most, and run soaked loads through another spin in the washer first.

If the dryer still runs cold after these seven checks, a part has most likely failed. The next two sections cover what a technician tests on each type.

Electric dryer not heating

An electric dryer heats with a coil of resistance wire inside a metal housing. Power reaches that coil only when every safety part in the circuit is closed, so one failed part anywhere along the line means no heat at all.

Power and voltage

Besides a tripped breaker, a burned terminal on the cord or a worn outlet can drop one side of the 240 volts. Scorch marks on the plug are a clue, but leave the cord and outlet to a technician or an electrician. Some apartment and condo buildings in Los Angeles get 208 volts instead of 240. A dryer rated for both still works there, but its element puts out roughly a quarter less heat, so drying simply takes longer. That's the building's wiring, not a fault in the dryer.

Heating element

An element fails a lot like a light bulb: the coil snaps and the circuit opens. Sometimes the break is easy to see, but often it isn't, so the real test is a resistance reading with the dryer unplugged. A coil that sags and touches its housing can also trip the breaker. Elements often burn out after months of weak airflow, which is why the vent should be checked whenever an element is replaced.

Thermal fuse

The thermal fuse is a one-time safety part that opens when the exhaust gets too hot. It doesn't reset. Depending on the model, a blown fuse either kills the heat or keeps the dryer from starting at all. Fuses blow for a reason, nearly always a clogged vent or lint around the blower. Put in a new fuse without fixing the airflow and it will blow again.

Cycling and high-limit thermostats

The cycling thermostat switches the heat on and off to hold the drum at the right temperature. The high-limit thermostat is the backup: it cuts the heat if the cycling thermostat fails or the airflow drops. If either one sticks open, the dryer stays cold. If the cycling thermostat sticks closed, the high limit keeps tripping, so the heat comes and goes and the clothes come out too hot.

Control board or relay

Newer electric dryers switch the element through a relay on the control board. When every part in the heat circuit tests good and the element still gets no power, the board is next. It's the least common cause on this list and usually the priciest part, so it should be confirmed with a meter before anyone orders one.

Gas dryer not heating

If you smell gas, don't start the dryer, flip light switches, or unplug anything. Leave the house and call SoCalGas, or 911, once you're outside. Don't look for the leak or try to fix it yourself. A dryer that won't heat is a repair. A gas smell is an emergency.

A gas dryer has the same thermal fuse and thermostats as an electric one, but the heat comes from a burner. Lighting that burner takes a short chain of steps, and where the chain breaks points to the part that failed.

How the burner lights

When the dryer calls for heat, the igniter starts to glow bright orange. Once it's hot enough, the flame sensor signals the gas valve to open, the gas lights, and the igniter shuts off. A technician watches this sequence through the viewing port, or with the lower front panel removed on models that don't have one. That one look usually shows which part to test.

Igniter doesn't glow

The igniter is a small, brittle part that cracks with age, so it's the usual suspect. Still, a blown thermal fuse, an open high-limit thermostat, or a failed flame sensor can also keep power from reaching it. For a real example, see how we traced a Frigidaire dryer that wasn't heating to a failed igniter.

Igniter glows, but the gas never lights

If the igniter stays lit for a long time and nothing happens, the flame sensor usually isn't switching over. If the igniter glows and then goes dark with no flame, check the gas supply first, then the gas valve coils.

Burner lights, then goes out and won't relight

This is the textbook sign of worn gas valve coils. A cold dryer lights normally, and the flame burns for a few minutes. Then the coils warm up, can no longer hold the valve open, and the dryer tumbles cold for the rest of the cycle. Coils are one of the most common heat repairs on gas dryers. They can test fine on a meter while cold, which is why a good technician watches a full heat cycle before changing them.

Thermal fuse and thermostats

These work the same way as on an electric dryer. A blown fuse or an open thermostat cuts power to the igniter, and if the fuse blew, find out why before you trust the dryer again.

When the vent is the real problem

A lot of "my dryer isn't heating" calls end with a clean vent rather than a new part. When the duct is packed with lint, hot air can't leave the drum. The thermostats cut the heat over and over, the clothes stay damp, and eventually the thermal fuse blows or the element burns out. Watch for these signs:

  • Loads that used to dry in one cycle now need two
  • The top of the dryer or the laundry room gets hot
  • Weak air at the outside vent hood, or a flap that stays shut
  • Lint around the door seal or behind the dryer
  • The dryer stops heating partway through a cycle

Lint is also a fire hazard. The U.S. Fire Administration counts about 2,900 home clothes dryer fires a year and names failure to clean as the leading cause. Long runs with several elbows, roof exits, and the shared vent stacks in condo buildings clog faster than a short duct through an outside wall. On a gas dryer, a blocked vent can also push exhaust back into the house. If your vent hasn't been cleaned in a year or two, book dryer vent cleaning along with the repair.

Is it safe to keep using a dryer that won't heat?

Tumbling on air alone won't hurt a dryer with a dead element or igniter. Stop using it right away, though, if you smell burning, if you smell gas, or if it stopped heating right after it got very hot. That last one usually means a blocked vent, so don't drop in a new fuse and carry on until the vent is clear.

What a no-heat repair costs in Los Angeles

Here is what the repairs in this guide typically cost in Los Angeles. Your exact price depends on the model and the part, and you get it after the $65 diagnostic, before any work starts. The $65 goes toward the repair. Prices for other appliances are in our appliance repair cost guide. If your dryer is getting old, our repair or replace guide helps you decide whether the fix is worth it.

ProblemTypical cost in Los Angeles
Not heating: heating element or gas valve parts$270 to $420
Gas dryer igniter or gas valve coils$230 to $420
Overheating or shutting off mid-cycle, thermal fuse$230 to $400
Takes too long to dry, airflow problems$230 to $410
Control board failure$300 to $520

When to call a technician

Call when the safe checks didn't bring the heat back, when the breaker trips again after a reset, when the thermal fuse has blown more than once, or when the fix means opening up a gas dryer. Work on the gas valve, burner, or gas line belongs with a technician.

We repair gas and electric dryers across Los Angeles, every day from 8 AM to 8 PM. The visit starts with a $65 diagnostic that covers the heat circuit, the burner on gas models, and the airflow through the vent, and the $65 is credited toward the repair if you go ahead. Every completed repair comes with a 183-day warranty on parts and labor. Call (213) 761-5757 before 11 AM for a good chance of a same-day visit, or see our dryer repair page. Appliance Insight is an independent repair company, not a manufacturer's service center.

Own an LG or a Samsung? Our LG dryer repair and Samsung dryer repair pages cover the brand codes and faults we see most. If the drum doesn't turn at all, start with our guide to a dryer that won't spin.

Frequently asked questions

Why is my dryer running but not heating?

On an electric dryer, the usual causes are one tripped half of the double breaker, a blown thermal fuse, or a broken heating element. On a gas dryer, it's a closed gas valve, a failed igniter, the flame sensor, or worn gas valve coils. A clogged vent can lead to most of these by making the dryer overheat.

Can a clogged dryer vent stop a dryer from heating?

Yes. Trapped heat trips the thermostats and can blow the thermal fuse, and either one shuts the heat off. Clear the vent before replacing parts, or a new fuse may blow too.

Does a dryer have a reset button for the heat?

Most home dryers don't. The thermal fuse is a one-time part and has to be replaced. Turning the breaker off for a few minutes can clear a glitch on electronic models, but it won't fix a failed part.

Why does my gas dryer heat for a few minutes and then stop?

Worn gas valve coils are the most common reason. The burner lights while the dryer is cold, then the coils warm up and let the valve close. A restricted vent that keeps tripping the high-limit thermostat can look similar, so check the airflow too.

Why does my electric dryer get warm but not hot?

Start with the vent and lint screen, then the load size. In some Los Angeles apartment buildings the supply is 208 volts, which cuts the heat by roughly a quarter. A thermostat that's starting to fail can also keep the drum cooler than it should be.

How much does it cost to fix a dryer that won't heat?

The safe checks cost nothing. In Los Angeles, a no-heat repair typically costs about $230 to $420, depending on the part. We give you one exact price after the $65 diagnostic, before any work starts, and the $65 goes toward the repair.

Sources: Whirlpool and Maytag dryer troubleshooting guides, LG dryer venting and installation guidance, SoCalGas instructions for a suspected gas leak, and the U.S. Fire Administration report on clothes dryer fires in residential buildings.

Give us a call if your dryer still runs cold after the safe checks, if the breaker keeps tripping, or if you have a gas dryer that needs opening up. A blocked vent or a failing part can turn into a fire risk, so it's worth getting it looked at. Call (213) 761-5757, the diagnostic is $65 and it comes off the bill if you go ahead, and every repair carries a 183-day warranty on parts and labor.