On an electric dryer, no heat usually means a failed heating element, a blown thermal fuse, or a bad cycling thermostat. On a gas dryer, it is often the igniter, the flame sensor, or the gas valve coils. A clogged vent can blow the thermal fuse again and again.
Check first: Make sure the dryer is on a heat setting, not air fluff. Electric dryers need both legs of a 240-volt circuit, so check for a tripped breaker. On a gas dryer, check that the gas valve behind it is open. For checks you can do first, see our gas and electric no-heat guide.
A dryer that needs two or three cycles usually has a clogged vent, a crushed or too-long vent duct, a weak heating element, or a moisture sensor coated with fabric softener residue.
Check first: Clean the lint screen, then disconnect the duct and feel the airflow at the outside vent while the dryer runs. Weak airflow means the vent needs cleaning; our dryer vent cleaning service clears the whole run. Wipe the metal sensor bars inside the drum with rubbing alcohol.
If nothing happens when you press start, the cause is often the door switch, a blown thermal fuse, the start switch, a broken belt, or a failed motor or control board.
Check first: Close the door firmly and check the breaker. If the dryer hums but the drum won't turn, unplug it right away; the belt or the motor is the likely cause. Our guide to a dryer that won't spin covers the drum problems.
A dryer that stops partway usually overheats and trips its safety thermostat or has a failing motor, a bad door switch, or a moisture sensor that ends the cycle too early.
Check first: Clean the lint screen and the vent, then run a short timed cycle. If the dryer stops and the top or the back feels very hot, airflow is the likely problem. Try a smaller load; a packed drum can stop the airflow too.
Thumping, squealing, or grinding usually comes from worn drum rollers, a worn idler pulley, a drum glide or bearing, or something caught in the blower wheel.
Check first: Check the pockets of the last load for coins, keys, or hairpins, and make sure the dryer sits level. Note when the noise happens, at startup or through the whole cycle, and what it sounds like. That helps us bring the right parts.
A burning smell often comes from lint built up around the heater or in the vent, a belt that is slipping, or a motor that is overheating. Lint is a serious fire risk.
Check first: Stop the dryer and unplug it. Clean the lint screen and look inside the housing with a flashlight for lint. Don't run it again until the vent and the lint buildup are cleared, and call us if the smell came from the motor or the wiring.
Unplug the dryer, and on a gas model, shut the gas valve before you move it or open any panel. If these checks don't solve it, book a diagnostic and we'll find the part that actually failed.
| Common repair | Typical cost |
|---|---|
| Not heating (element, fuse, or thermostat) | $270 to $420 |
| Takes too long to dry | $230 to $410 |
| Drum not turning (belt, roller, or motor) | $240 to $430 |
| Gas dryer igniter | $230 to $420 |
Typical repair cost in Los Angeles; exact price after the $65 diagnostic, which goes toward the repair.
In most cases, yes. Dryers are simple machines, and most failures come from parts that cost far less than a new dryer. Most dryers are worth fixing; our repair or replace guide explains why, and when the 50% rule says a new one makes more sense.
Wondering what other repairs cost? See the typical prices in our dryer repair cost guide.
New dryer? We handle gas dryer hookup and electric dryer installation.
“He came on short notice on a Sunday evening to repair our Whirlpool dryer which wasn't spinning. He diagnosed the problem quickly and our dryer was working smoothly within an hour!!”
“Stan did a fantastic job putting on a belt for my old Maytag dryer. He really went the extra mile and stayed to listen for any more problems.”
“Stan came over same day, had everything needed to repair the dryer and worked very efficiently.”
Read more on our reviews page.