

Most dryer calls in Pasadena come down to four things: no heat, no tumble, won't start, or clothes that take two cycles. Here's what usually causes each one, and what you can safely check before you call.
Most Pasadena houses dry with gas. First make sure the gas shutoff behind the dryer is fully open, especially if the dryer was just moved. If the igniter glows and then goes out without lighting the burner, the gas valve coils are the usual cause. If it never glows, we test the igniter, the flame sensor and the thermal fuse.
An electric dryer needs 240 volts from a double breaker. If one half of that breaker trips, the drum can still turn while the heat stays off, so switch the dryer's breaker fully off and back on first. If it still runs cold, the usual suspects are the heating element, the thermal fuse and the high-limit thermostat.
If the motor hums but the drum doesn't move, the belt has usually snapped. Thumping, squealing or a grinding sound points to worn drum rollers, an idler pulley or drum glides. Keep running a squealing dryer and a cheap roller job can turn into a motor.
Check that the door is fully closed, the child lock is off and the breaker hasn't tripped. After that, we test the door switch, the start switch, the thermal fuse and the control board.
This is the one we see most in Pasadena. Laundry in a detached garage or on a back service porch often means a long vent run, and foil ducts behind stacked units get crushed against the wall. A quick test: pull the duct off the back of the dryer and run a timed dry. If the clothes dry normally, the problem is the vent, not the dryer. We check the vent on every dryer call, and we also offer dryer vent cleaning.
Samsung and LG are the dryers we see most in Pasadena apartments and newer houses. These are the codes that bring most of those calls, with what LG and Samsung say they mean:
| Code | What it means | What to try first |
|---|---|---|
| LG d80, d90, d95 | Exhaust airflow is restricted by about 80, 90 or 95%. On a gas LG, d80 can also mean no gas is reaching the dryer. | Clean the lint filter, check the duct for kinks and make sure the outside flap opens. At d95, stop using it until the vent is cleared. |
| LG nP | No current at the heater, usually a home wiring or outlet problem. | Switch the breaker off for 10 seconds. If it still won't heat, the 240 V outlet needs checking. |
| LG tE1, tE3 | Temperature sensor (thermistor) problem. | Unplug, hold Start/Pause for 5 seconds, plug back in. If it returns, the sensor needs testing. |
| LG HS | Humidity sensor error. Cycles can run about 2.5 hours and still leave clothes damp. | Wipe the sensor bars under the lint filter with a damp cloth. |
| Samsung hE, HC | Heating error: the dryer is running too hot. | Clean the lint screen and the vent. On electric models, low voltage can also cause it. |
| Samsung tS, tC, tO | Temperature or temperature sensor problem. | Clean the lint screen and the vent. If it continues, the sensor needs testing. |
| Samsung HC2 | Gas ignition error. | Make sure the gas valve is open. If it is, the igniter or valve coils need testing. |
| Samsung dC, dE, dF | Door, latch or door sensor problem. | Close the door fully and check that no laundry is caught in it. |
Code meanings are from LG's and Samsung's US support pages. Exact codes vary by model.
Appliance Insight is an independent repair company, not a factory-authorized service center for LG, Samsung or any other brand. If your dryer is still under the manufacturer's warranty, contact the manufacturer first.
The diagnostic visit is $65, and it comes off the bill if we do the repair. A dryer that won't heat might need a small thermal fuse, a heating element, an igniter or valve coils, so we test it before quoting. You get one exact price for parts and labor, and nothing is replaced until you approve it.
Often, yes. Call (213) 761-5757 before 11 AM and there's a good chance we can come the same day. Otherwise it's usually the next day.
On a gas dryer it's usually the igniter, the gas valve coils or the thermal fuse, or the gas shutoff isn't fully open. On an electric dryer it's often a tripped half of the 240 V breaker, the heating element, the thermal fuse or the high-limit thermostat. A clogged vent can cause either one to overheat and shut the heat off.
Most of the time it's the vent, not the dryer. Long vent runs from garages and service porches are common in Pasadena and fill with lint. Pull the duct off the back and run a timed dry: if the clothes dry normally, clean the vent. If they don't, the heating system or a sensor needs testing.
Yes. Gas and electric, front-load, stacked washer and dryer units, washer-dryer combos, vented and ventless dryers.
LG says d80, d90 and d95 mean exhaust airflow is restricted by about 80, 90 or 95%. On a gas LG, d80 can also mean no gas is reaching the dryer. Clean the lint filter and check the duct and the outside flap. If the code stays, the vent needs cleaning or the dryer needs testing.
Samsung lists hE and HC as heating errors, meaning the dryer is running too hot. Clean the lint screen and the vent first. On electric models low supply voltage can also cause it. If the code comes back, a sensor, the heater or the control needs testing.
Usually. Most dryer failures come down to one part, like a belt, a thermal fuse, rollers or an igniter. If the repair doesn't make sense for the age of the dryer or the price of the part, we'll tell you, and you only pay the $65 diagnostic.
We check the vent on every dryer call, and we also offer dryer vent cleaning as its own service.
Samsung, LG, Whirlpool, Maytag, GE, Kenmore, Bosch, Electrolux and the other major brands.
No. Appliance Insight is an independent repair company and isn't affiliated with any appliance brand. If your dryer is still under the manufacturer's warranty, contact the manufacturer first. Our own repairs carry a 183-day parts and labor warranty.
All of Pasadena, 91101 to 91107, including East Pasadena, Hastings Ranch, Bungalow Heaven and Linda Vista, plus Altadena, South Pasadena and San Marino. For other appliances, see our Pasadena appliance repair page.
Yes. 183 days on parts and labor. If the same problem comes back in that window, we come back and fix it at no charge.