LG Dishwasher Not Draining: Why Water Stays in the Bottom and How to Fix It

Water left in the bottom of an LG dishwasher usually comes from one of three things: a clogged filter, a kinked drain hose, or a blocked air gap or disposal connection. You can check all three yourself in about 20 minutes without tools. If the dishwasher hums during the drain but the water doesn't move, or the OE code comes back after cleaning, the drain pump is the next suspect, and that is a job for a technician.

Is some water in the bottom normal?

Yes, a little. Most dishwashers keep a small amount of water down in the sump, under the filter, so the seals stay wet and drain odor stays out. That water sits below the filter and you only see it when you take the filter out.

It is not normal when water covers the tub floor, sits above the filter, or is still there an hour after the cycle ended. That means the dishwasher tried to drain and couldn't.

Why the dishwasher beeps, blinks or shows OE

When an LG dishwasher can't empty the tub in time, it stops the cycle, beeps and shows OE on the display. OE simply means "not draining." The code doesn't tell you why, so the steps below go from the easiest cause to the hardest. For the other codes, see our LG dishwasher error codes guide.

How to force drain an LG dishwasher

Try this first. If the drain works, the water leaves in a few minutes and you know the pump is alive.

  1. Close the door and press Power.
  2. Press and hold Start for about 3 seconds. The remaining time disappears and "--" shows on the display.
  3. Wait. LG says the dishwasher drains for 2 to 3 minutes and then turns itself off.

Some LG models have a Cancel and Drain function on a two-button combination instead. LG gives Delicate plus Dual Control as one example, but the pair differs by model, so check the labels on your panel or the owner's manual. On models with neither option, LG suggests starting any cycle, letting it run for 45 seconds (the first 45 seconds of every cycle is drain only), and then turning it off.

If the water is still there after a forced drain, something is blocking it. Move on to the checks below.

Step by step: what you can fix yourself

Turn the dishwasher off before you reach into the tub, and give hot water time to cool. If the tub is full, scoop most of the water out with a cup and a sponge first so it doesn't run over the door when you lean in.

1. Clean the filter

This fixes most drain problems. Pull out the lower rack and pick out anything large: food, labels, broken glass, fruit pits. Then twist the round mesh filter counterclockwise and lift it out together with the flat stainless steel filter under it.

Rinse both under warm running water with a soft brush. Watch your fingers, because the stainless filter has sharp edges. Put them back in reverse order and turn the mesh filter clockwise until it clicks. A filter that isn't seated properly lets debris into the pump.

LG recommends cleaning the filter after every load for the best results, and at least once a month in hard water areas. Los Angeles water is hard, so scale builds up on the mesh faster here. Our hard water dishwasher guide covers that part.

2. Check the drain hose under the sink

Open the sink cabinet and find the ribbed hose, usually white or gray, running from the dishwasher side. Look for a kink, a sharp bend, or a trash can or box pressing on it. Straighten it out.

The hose can also kink behind the dishwasher, where you can't see it. This happens when the unit is pushed back into its opening after an install or a floor repair.

3. Clear the air gap

Some kitchens have a small chrome or white cap on the sink deck next to the faucet. That is the air gap, and the dishwasher water passes through it on the way to the drain. Pull off the cover and the plastic cap under it, clear debris with a toothpick or small brush, and flush it with hot water. LG suggests a turkey baster for this. If water spits out of the air gap during a drain, it is blocked.

4. Run the garbage disposal

In most kitchens the dishwasher drains into the disposal. Food sitting in the disposal blocks the dishwasher too. Run the disposal with cold water for 20 to 30 seconds, then force drain the dishwasher again.

5. Test it

Run an empty Normal or Heavy cycle with no dishes and no detergent, as LG suggests, and watch whether it drains at the end. If it does, run one more empty cycle with a cup of white vinegar or a dishwasher cleaner to clear out the grease left in the sump and hose.

OE on a new dishwasher or a new disposal

If OE shows up on the very first cycles, the problem is almost always the installation. LG lists these requirements:

  • The drain hose is no longer than 12 feet, with no extensions added.
  • The end of the hose sits between 12 and 40 inches above the floor.
  • There is no slack or kink behind the dishwasher.
  • On a new disposal, the knockout plug inside the dishwasher inlet has been removed. While that plug is there, the dishwasher can't drain at all.

These are fixes for the installer or a plumber.

Signs the drain pump has failed

If the filter, hose, air gap and disposal are clear and the dishwasher still won't drain, the problem is inside the machine:

  • Humming or buzzing, no water moving: something is jammed in the pump impeller (glass, a bone, a pit), or the pump motor is failing.
  • Total silence when it should drain: the pump isn't getting power, or the pump or the control board has failed.
  • Grinding or rattling during the drain: debris is in the pump housing.
  • Water drains, then some comes back into the tub: the check valve that stops dirty water from flowing back may be stuck open.

The drain pump sits under the sump, so getting to it means pulling the dishwasher out or taking the base apart. Running the dishwasher again and again with a drain error can make a small repair bigger, so it's better to stop and have it checked.

What a technician does

We test the drain pump and the power reaching it, check the sump, check valve and drain path, and read any stored codes. The diagnostic visit is $65, and that amount comes off the bill if you go ahead with the repair. Repairs come with a 183-day warranty on parts and labor.

If you're in Los Angeles, book LG dishwasher repair online, or see our dishwasher repair page for other brands. For Bosch, GE, Samsung and Whirlpool, see our dishwasher not draining guide for every brand.

How to keep it draining

  • Scrape plates into the trash. Bones, pits, rice and paper labels end up in the filter.
  • Clean the filter at least once a month, more often with hard water.
  • Run the garbage disposal before you start the dishwasher.
  • Keep things in the sink cabinet away from the drain hose.

FAQ

Why is there water standing in the bottom of my LG dishwasher?

A small amount under the filter is normal. Water on the tub floor or above the filter usually means a clogged filter, a kinked drain hose, a blocked air gap or a full disposal. If all four are clear, the drain pump may have failed.

How do I force my LG dishwasher to drain?

Turn it on, then press and hold Start for about 3 seconds. The display shows "--", the dishwasher drains for 2 to 3 minutes and turns off. Some models use a two-button Cancel and Drain combination instead, so check your panel.

Why is my LG dishwasher beeping and blinking and not draining?

The dishwasher stopped because it couldn't empty the tub, and it is showing the OE code. Clean the filter, check the drain hose and air gap, run the disposal, then force drain it. If OE comes back, have the drain pump checked.

Can I keep using my LG dishwasher if it isn't draining?

It's better not to. Dirty water stays in the tub, starts to smell, and the next cycle will stop with the same code. Repeated runs with a drain fault can also overwork the pump.

How much does it cost to fix an LG dishwasher that won't drain?

A clogged filter or kinked hose costs nothing to fix yourself. If the pump or another part has failed, we give you one price for the part and labor after the $65 diagnostic, and the $65 is credited toward the repair.

Why won't my LG dishwasher drain when it shows AE or FE instead of OE?

AE and FE are not drain codes. LG uses them when the leak sensor finds water in the base or the tub takes in too much water, often because of suds from dish soap or too much detergent. Check for water on the floor and suds in the tub, and use only dishwasher detergent. If the floor is dry and AE stays, LG says to unplug the dishwasher or switch off its breaker and request service. Our LG error codes guide covers AE in detail.

Why does my LG dishwasher gurgle or growl while it drains?

LG says a growling, air sucking sound is normal on some cycles, when the dishwasher pulls air through to clean the filter. Too much detergent or food debris in the drain can make it louder. A loud gulping sound, or a kitchen sink that drains slowly, points to a clog in the drain pipe that needs clearing. Squealing or grinding is different: LG says it can mean a pump problem.

Give us a call if your LG dishwasher still won't drain after you've cleaned the filter and checked the hose, or if the OE code keeps coming back. Water left standing in the tub starts to smell within a day or two, so it's worth getting it looked at. Call (213) 761-5757, the diagnostic is $65 and it comes off the bill if you go ahead.