| Code | What it means |
|---|---|
| AE, E1, FE | Leak or overfill, water reached the base |
| OE | Not draining |
| IE | Not filling with water |
| bE | Too many suds |
| LE | Wash motor isn't working normally |
| HE | Water isn't heating |
| tE | Temperature sensor problem |
| nE | Vario pump impeller not turning, or a dish is touching it |
| PE | Water level sensor (some older models) |
| F31, F35 | Heat Dry fan or Heat Dry temperature (Dynamic Heat Dry models) |
| F37 | Auto Open Door isn't working |
| CL | Control Lock is on, not a fault |
| PF | Power went out during the cycle, not a fault |
AE means the leak sensor in the base of the dishwasher found water. FE means more water came in than the dishwasher expected. LG lists them together, and some older displays show E1 instead of AE. When you see either one, the dishwasher keeps running the drain pump to get the water out.
The usual causes, according to LG:
If there's water on the floor, turn off the water valve under the sink and switch off the power before you clean up. If you poured water into the Heat Dry blower on a built-in model, don't pull the dishwasher out. Call for service.
If there's no water on the floor and AE won't go away, LG says to unplug the dishwasher, or turn off its switch or breaker, and request service. When AE keeps coming back with normal detergent, we usually find a worn door gasket, a cracked hose or a leaking pump seal. Water sitting in the base can damage the floor under the dishwasher, so don't keep running it. Our LG dishwasher repair page covers how we track down leaks.
OE means water isn't draining out of the tub all the way. Most of the time the filter is clogged.
What to check:
A little water under the filter is normal. LG leaves it there on purpose to keep sewer smell out. If water still sits above a clean filter and the hose is fine, the drain pump or a blockage further down is the usual cause, and that needs a technician.
For the full walkthrough, including how to force drain and how to tell when the drain pump has failed, see LG dishwasher not draining.
IE means the dishwasher didn't get enough water in the time it expected.
If the water supply is fine and IE keeps coming back, the inlet valve or its screen is the usual problem. In older Los Angeles buildings, an old shutoff valve under the sink that doesn't open fully can cause it too.
bE means the dishwasher found too much foam and stopped so the suds don't leak out. It's almost always the detergent.
To clear the suds, LG suggests this: set the rinse aid to L0, don't add detergent, put a bowl with about 7 oz of milk in the middle of the upper rack, and run Standard with Extra Dry and Rinse. Repeat if you still see foam, then set the rinse aid back to where it was.
If bE shows up and there are no suds in the tub, have the dishwasher checked.
These codes point to a part, and there isn't much to try at home. Turning the power off for a few minutes and starting again is fine once. If the code comes back, book a repair.
These codes show up on LG models with Dynamic Heat Dry.
For F31 and F35, LG says to request service. For F37, call if the code comes back with nothing in the way.
CL means Control Lock is on. The buttons don't respond, but nothing is broken. On many LG dishwashers you hold the Control Lock button for 3 seconds. On others it's Half Load and Energy Saver together for 3 seconds. The lock stays on after you turn the dishwasher off, so it can look like the panel died overnight.
PF means the power went out during a cycle. Press Start to pick up where it stopped. If you see PF often without a power outage, have the outlet or breaker for the dishwasher checked.
Most codes clear once you fix the cause. To reset, turn the dishwasher off, unplug it or switch off its breaker for a few minutes, then turn it back on and start a cycle. If the same code comes back right away, resetting won't fix it. Running the dishwasher again and again with a leak or drain code can turn a small repair into a bigger one.
If your LG dishwasher has Wi-Fi, the LG ThinQ app can run Smart Diagnosis and show what the dishwasher is reporting. It's worth a try before you call.
If the dishwasher won't turn on at all or the buttons don't respond, see LG dishwasher won't turn on.
Call when the same code keeps coming back after the checks above, when there's water on the floor, when the dishwasher stops heating or drying, or when you see a part code like LE, HE or tE.
We repair LG dishwashers at home across Los Angeles. The diagnostic is $65 and goes toward the repair if you go ahead, and completed repairs carry a 183-day warranty on parts and labor. Typical prices for LG dishwasher repairs are on our LG dishwasher repair page. Appliance Insight is an independent repair company, not affiliated with or authorized by LG.
Related: LG dishwasher repair • Dishwasher repair in Los Angeles • LG appliance repair
AE means the leak sensor in the base found water, or the dishwasher took in more water than it expected. The most common cause is suds from dish soap or too much detergent. Check for water on the floor, use dishwasher detergent only and make sure the dishwasher is level. If AE stays on and there's no water on the floor, unplug the dishwasher and call for service.
Let the tub cool for 30 minutes, then take out and rinse the filter. Check that the drain hose under the sink isn't kinked and run the garbage disposal if the dishwasher drains through it. On many models you can pump out standing water by holding Start for 3 seconds. If water still sits above a clean filter, the drain pump or a blockage further down usually needs a technician.
bE means too many suds. It almost always comes from dish soap or too much detergent. Switch to powder or tablets made for dishwashers and run the suds-clearing cycle LG describes. If bE shows up with no suds in the tub, have the dishwasher checked.
Turn it off, unplug it or switch off its breaker for a few minutes, then turn it back on and start a cycle. If the same code comes back right away, resetting won't fix it, and a part has likely failed.
No. CL means Control Lock is on, so the buttons don't respond. Hold the Control Lock button, or Half Load and Energy Saver together on some models, for 3 seconds to turn it off.
LG's US error code guide does not list 6E, 1E or 0E. On the display, the letters b, I and O can look a lot like 6, 1 and 0, so check whether the code is really bE (too many suds), IE (no water coming in) or OE (not draining) and use the matching section above. If the code does not match anything in LG's list, write it down with your model number and give us a call.
According to LG, that beep is a high temperature alert. It sounds when you open the door after a steam, heated wash, heated rinse or drying cycle while the inside is still hot. Let it cool before you unload. If an error code shows on the panel at the same time, look it up in the table above.