Some water is fine. GE, for example, says that on its models without an ultra-fine filter, 1 to 2 cups of clean water covering the bottom of the tub is normal. Most other brands keep a small amount in the sump under the filter so the seals don't dry out.
It's a drain problem when the water is dirty, sits above the filter, is more than an inch deep, or is still there an hour after the cycle ended. Gurgling at the sink, water backing up into the sink and a cycle that stops with an error code all point the same way.
Turn the dishwasher off and, if you can reach the plug, unplug it. Put towels on the floor in front of the door. Take out the lower rack and bail the water out with a cup, then soak up the rest with a sponge or towels. A wet/dry shop vac works well if you have one. Some of the water may be hot right after a cycle, so give it a few minutes.
If your model has a cancel or drain function, try that first (see the brand table below). If the pump can push the water out on command, the problem is more likely a partial clog than a dead pump.
This is the most common cause, and manufacturers like Whirlpool and Bosch put it first on their lists. The filter sits on the floor of the tub, in a back corner or around the base of the lower spray arm. On most newer models you twist the round filter a quarter turn counterclockwise and lift it out. Some older ones need a screwdriver, so check the manual.
Rinse it under warm water and scrub the mesh with a soft brush, like an old toothbrush. Don't use anything abrasive on the fine mesh. Look into the opening under the filter too: pieces of glass, bones, fruit pits, paper labels and twist ties end up there. Be careful, because broken glass is common.
Put the filter back and lock it in place. A filter that isn't seated right lets debris straight into the pump.
If the filter keeps clogging, hard water can be part of the story. Los Angeles water leaves a lot of scale, and we cover that in our hard water dishwasher guide.
Open the sink cabinet and follow the ribbed hose that comes from the dishwasher. Straighten any kinks and move anything that presses on it, like a trash bin or cleaning bottles.
The part you can't see matters too. Samsung says the most common cause right after an installation is the dishwasher sitting on its own drain hose behind the kick plate. If the unit was recently pushed back into its opening, the hose may be pinched underneath it.
The hose needs to rise before it drops into the drain. Whirlpool, KitchenAid and Maytag ask for a high loop at least 20 inches above the floor, or an air gap if the hose connects lower than that. Without the loop, dirty water from the sink can flow back into the dishwasher.
Old hoses also collect sludge inside. If yours is stiff or discolored, replacing it is cheap.
Many kitchens in California have a small chrome or plastic cap on the sink deck, next to the faucet. That is the air gap. Dishwasher water passes through it on the way to the drain. If water spits out of it during a drain, it's blocked.
Pull off the cover, unscrew or lift the inner cap, and clear the gunk with a small brush or a toothpick. Flushing it with hot water helps.
Most built-in dishwashers drain into the disposal. If the disposal is full of food, the dishwasher can't push its water through. Run the disposal with cold water for about 20 to 30 seconds, then try draining the dishwasher again. Never put your hand inside a disposal to check it.
Here is a quick way to tell where the blockage is, suggested by Samsung: run water in the sink for about 30 seconds. If the sink itself drains slowly or backs up, the clog is in the house plumbing, not the dishwasher, and a plumber is the right call.
This one causes a lot of confusion. A new garbage disposal comes with a plastic plug inside its dishwasher inlet. Until someone knocks it out, the dishwasher has nowhere to drain. Whirlpool, Bosch, GE, Samsung and Frigidaire all mention it.
If the problem started right after a new disposal was installed, this is almost certainly the cause. With the power to the disposal off, the plug is knocked out through the inlet with a screwdriver and a hammer, and the loose piece is fished out of the disposal. If you're not comfortable doing that, the installer or a plumber can fix it in a few minutes.
Regular dish soap makes so much foam that the pump can't move the water, and the cycle may stop with standing suds. GE also warns that too much dishwasher detergent can do the same. If someone used dish soap by mistake, bail out the suds, wipe the tub, and run a rinse cycle with no detergent.
Don't pour drain cleaner into the dishwasher. GE advises against it, and it can damage the plastic parts and seals.
The exact buttons depend on the model, so check the manual if yours looks different. These are the steps the manufacturers give:
| Brand | Drain error | How to cancel and drain |
|---|---|---|
| Bosch | E24, E25 | Hold Start or the "Reset 4 sec." button for about 4 seconds. The water drains in about a minute. |
| GE | Varies by model | Touch Start/Reset to cancel. GE's manual says the pump then runs for about 105 seconds. |
| LG | OE | Hold Start for about 3 seconds. It drains for 2 to 3 minutes, then turns off. |
| Samsung | 5C or 5E | Samsung lists no drain button. Clear the drain path, then start a new cycle. |
| Whirlpool, KitchenAid, Maytag | Varies by model | Hold Cancel to drain, then start a new cycle. |
Bosch adds one more detail: E24 points to a blocked filter or drain hose, while E25 means the drain pump itself is blocked or its cover is loose. The pump cover sits under the filter. Bosch says it can be pried off with a spoon to clear debris, but watch for glass. For more on Bosch, see our Bosch dishwasher repair page.
For LG models, our LG dishwasher not draining guide goes through the OE code step by step.
If the filter, hose, air gap and disposal are all clear and the water still won't leave, the problem is inside the machine. These are the usual signs:
Getting to the pump usually means pulling the dishwasher out of its opening and taking the base apart. Running a dishwasher again and again with a drain fault can overheat the pump, so it's better to stop and have it checked. If the dishwasher is old and the pump has failed, our repair or replace guide can help you decide whether to fix it.
We test the drain pump and the power reaching it, inspect the sump, the check valve and the whole drain path, and read the stored error codes. The diagnostic visit is $65, and that amount comes off the bill if you go ahead with the repair. Every repair comes with a 183-day warranty on parts and labor.
Here is what drain repairs typically cost in Los Angeles. The exact price comes after the $65 diagnostic, which goes toward the repair.
| Repair | Typical cost |
|---|---|
| Not draining or standing water (pump, hose, filter clog) | $210 to $360 |
| Error code or control board failure | $270 to $480 |
Many drain calls end without any new part: the pump is cleared of glass or a pit, the hose is replaced or rerouted, and the dishwasher drains again. Prices for other appliances are in our appliance repair cost guide.
If you're in Los Angeles, you can book dishwasher repair online. If you call before 11 AM, ask about same-day appliance repair. We work on all major brands, including LG, Bosch and Miele.
A little clean water under the filter is normal. Dirty water on the tub floor or above the filter usually means a clogged filter, a kinked drain hose, a blocked air gap, a full garbage disposal or a knockout plug left in a new disposal. If all of those are clear, the drain pump may have failed.
The blockage is further down the line. Check the drain hose for kinks, clean the air gap, run the disposal and make sure the sink itself drains. If everything is clear and the pump hums or stays silent, the pump or its power supply is the problem.
The knockout plug inside the disposal's dishwasher inlet was probably not removed. Until it is, the dishwasher water has nowhere to go. The installer or a plumber can knock it out in a few minutes.
Use the cancel function. On Bosch, hold Start or Reset for about 4 seconds. On LG, hold Start for about 3 seconds. On GE, touch Start/Reset. On Whirlpool, KitchenAid and Maytag, hold Cancel. Button names vary by model, so check the manual if yours is different.
It's better not to. Dirty water stays in the tub and starts to smell. The next cycle will likely stop with the same error, and repeated runs can overwork the drain pump.
A clogged filter, kinked hose or blocked air gap costs nothing to fix yourself. In Los Angeles, a drain repair typically costs $210 to $360. The exact price comes after the $65 diagnostic, which goes toward the repair.