Bosch Dishwasher Repair in Los Angeles

Appliance Insight repairs Bosch dishwashers in homes across Los Angeles, from 100 Series models to the 800 Series with CrystalDry and the Benchmark line. Most calls are about an error code, water left in the tub or dishes that come out wet. The technician tests the dishwasher on the first visit and gives you one price before any work starts.

  • $65 diagnostic, credited to the repair
  • 183-day warranty on parts and labor
  • One price before any work starts
  • Phones 8 AM to 8 PM every day, online booking 24/7
  • Licensed & insured, CA license A 50129, BBB Accredited

We're an independent repair company and aren't affiliated with or authorized by Bosch. Bosch covers a new dishwasher for 1 year on parts and labor, so if yours is newer than that, call Bosch first.

Technician servicing the drain area of a built-in dishwasher in a Los Angeles kitchen

On This Page

Bosch Dishwasher Problems We Fix

We repair the drain pump, the heat pump that circulates and heats the water, the inlet valve, the door latch and hinges, the leak protection system and the control board. These are the problems Los Angeles owners call us about most.

Bosch dishwasher not draining (E24, E25)

Water sitting in the bottom after a cycle means the dishwasher isn't pumping it out. Bosch shows E24 when the drain is blocked and E25 when the drain pump is jammed or its cover has come loose. Turn the dishwasher off, twist out the filter and rinse it under the tap with a soft brush and a little dish soap. Under the filter sits a small pump cover. Bosch suggests prying it up with a spoon until it clicks, lifting it off and soaking up the water and debris with a sponge. Be careful, because broken glass often ends up there.

If the pump area is clean, look past the dishwasher. A kinked drain hose, a new garbage disposal with the knockout plug still inside, or a clogged air gap on the sink will all keep it from draining. When the code comes back after those checks, we test the drain pump and its wiring. Our guide to a dishwasher not draining covers the same checks for every brand.

Water under the dishwasher or E15

E15 means the safety switch found water in the base, so the leak protection stopped the dishwasher. Bosch's advice is short: turn off the water supply and call for service. You'll find tips online about tilting the dishwasher to dry the base. That can clear the code for a day or two, but the water came from a leak, and the leak is still there.

The usual sources are the drain pump seal, a hose or clamp, the inlet valve, the door gasket or a crack in the sump. Newer models with a text display may show E:30-00 or E:31-00 for the same alarm. More on finding a leak in our leaky dishwasher guide.

Not drying, or plastics come out wet

Bosch dishwashers have no exposed heating element in the tub, so they dry differently from many other brands. 100 and 300 Series models use PureDry, a closed condensation system. 500 Series models with AutoAir open the door a little when the cycle ends. 800 Series and Benchmark models add CrystalDry, which uses a mineral called zeolite to turn moisture into heat.

Plastic items stay damp on every model, and Bosch notes that water spots on plastic can't always be avoided. If glasses and plates come out wet too, raise the rinse aid setting and keep the dispenser full. On 800 Series models the setting runs from r:00 to r:06 and ships at r:05. Extra Dry or Sanitize also helps. If dishes are cold as well as wet, the heater may have failed.

White film, spots and hard water (E12)

A white film on glasses or on the tub walls is mineral scale, and we hear about it a lot in Los Angeles. Bosch recommends running its descaler every 3 to 6 months. E12 means scale has built up in the heat pump. Among US models, only Benchmark has a built-in water softener. On those, set the water hardness under the basic settings (H:00 to H:07) and fill the salt container with dishwasher salt, never table salt.

A higher rinse aid setting cuts down on spots. If the film stays after descaling, or cycles run much longer than they used to, the heater may be scaled and needs testing. Our article on hard water and dishwashers covers this in more detail.

Dishes not clean or gritty

Bosch tells owners to check the filter for food after every wash, because a clogged filter puts grit back on the dishes. Check that the spray arms spin freely, that their holes are clear and that nothing tall blocks them. If the wash is still weak with a clean filter, the heat pump may be failing, and codes like E01, E09 or E21 point the same way.

Not filling, or the water tap light is on (E16, E17, E18)

These codes, and the water tap light, mean water isn't coming in as it should. Open the valve under the sink all the way and look for kinks in the inlet hose. Bosch asks for a flow of about 10 liters a minute. On models with AquaStop the inlet hose is part of the leak protection, so a damaged hose gets replaced, not patched. E14 points to the flow meter and needs a technician.

Won't start, or how to reset it

Check the breaker and the outlet, and make sure the door closes all the way. To cancel a cycle and reset, hold Reset 4 Sec., or Start on models without that button, for about 4 seconds. The dishwasher drains for about a minute, then you press On/Off. For many codes, Bosch's first step is to switch off the breaker for 30 seconds. If all the lights flash and it beeps, switch it off, cut the power for at least 2 minutes and try again.

E27 means the voltage reaching the dishwasher is too low, which is a question for an electrician. If it still won't start, we test the door switch, the power supply and the control board.

Door falls open or won't latch

When the door drops open, a hinge spring or its cable has usually broken or slipped off. On panel-ready models the springs are matched to the weight of the custom panel. A door that won't latch, or a dishwasher that stops partway through, points to the latch and door switch. E06 is a door sensor fault.

Grinding or humming noise

Bosch dishwashers are quiet, so a new noise stands out. Grinding usually means glass, a pit or a bone has reached the drain pump or the space under its cover. Humming while no water moves can be a jammed pump. We find the source before replacing anything.

What Do Bosch Dishwasher Error Codes Mean?

The meanings below come from Bosch's US error code list. Newer models may show four-digit codes, such as E3100 in place of E15. Write down the exact code and the model number (E-Nr) before you call.

CodeWhat Bosch says it meansWhat to try first
E01Heat pump motor circuit faultBreaker off for 30 seconds. If it returns, book a repair.
E04Heater electronics faultNot a home fix. Book a repair.
E06Door sensor faultBreaker off for 30 seconds. If it returns, book a repair.
E09Heat pump heater faultBreaker off for 30 seconds. If it returns, book a repair.
E12Scale in the heat pumpRun a descaler cycle.
E14Flow meter or fill faultNot a home fix. Book a repair.
E15 (E3100)Water in the base, leak protection onTurn off the water and book a repair.
E16, E17Water isn't flowing inCheck the supply valve and the inlet hose.
E18Water level too lowOpen the supply fully and check the hose.
E21Heat pump blockedBreaker off for 30 seconds. If it returns, book a repair.
E22 (E9240)Filter, drain or air gap blockedClean the filter, then check the pump cover, hose and air gap.
E23Drain pump blocked or failedNot a home fix. Book a repair.
E24Drain blockedCheck the hose, disposal plug, air gap and pump cover, then reset.
E25Drain pump blocked or cover looseLift the pump cover, clear it and click it back in.
E27Supply voltage too lowBreaker off for 30 seconds. If it returns, call an electrician.

If a code comes back after the checks and a reset, a part needs testing. Bosch itself tells owners to call for service on E04, E14, E15 and E23.

Bosch Dishwashers We Repair

100 and 300 Series. These are Bosch's most common dishwashers, and they use PureDry drying. 300 Series and higher models have AquaStop leak protection on the inlet hose.

500 Series. These use AutoAir drying, which opens the door when the cycle ends.

800 Series and Benchmark. These use CrystalDry drying, which handles plastics better. Benchmark models add a built-in water softener and TimeLight, which shows the time left on the floor.

Panel-ready and 18-inch models. Fully integrated dishwashers with a custom cabinet front, and compact 18-inch units for smaller kitchens.

Many repairs mean sliding the dishwasher out of the cabinet. The technician protects the floor and the panel, then sets the unit back level. When you book, send us the model number (E-Nr) and the FD number from the rating label inside the door. Bosch says it keeps genuine spare parts available for up to 15 years, and we check parts by model number before the visit.

Things to Check Before You Call

  • Write down the code, plus the E-Nr and FD numbers from the label inside the door.
  • Switch the breaker off for 30 seconds and back on. Bosch lists this as the first step for many codes.
  • Make sure the door closes fully and the water valve under the sink is open all the way.
  • Take out the filter, rinse it and check that the pump cover under it clicks into place.
  • Run the garbage disposal, look for kinks in the drain hose and clear the air gap if your sink has one.
  • Check that the rinse aid dispenser isn't empty.

If you see E15 or water on the floor, skip the checks. Turn off the water to the dishwasher and don't run it until it's repaired.

How We Repair Bosch Dishwashers

The technician reads the code, asks what happened and runs the dishwasher to see the fault. Simple causes come first: the filter, the drain path and the water supply. Then come the pumps, heater, inlet valve, door latch and leak protection, with the control board last. A part gets replaced only after it tests bad.

You get one price before any work starts. If a Bosch part has to be ordered by model and FD number, we come back once it arrives. Before the technician leaves, the dishwasher runs a fill, wash and drain, and the base is checked for water.

How Much Does Bosch Dishwasher Repair Cost in Los Angeles?

The diagnostic visit is $65. If you go ahead with the repair, the $65 goes toward it. If you don't, you pay only the $65. The table shows the typical repair cost in Los Angeles. You get the exact price after the diagnosis. Prices for other appliances are on our appliance repair cost page.

RepairTypical cost in Los Angeles
Not draining or water in the tub (E24, E25)$210 to $360
Leak or water in the base (E15)$230 to $400
Not cleaning well$200 to $360
Not filling with water$200 to $340
Won't start or no power$230 to $390
Loud noise during the cycle$210 to $360
Door not latching$190 to $300
Detergent dispenser not opening$190 to $330
Error code or control board$270 to $480

The final price depends on the part and on how the dishwasher is installed. Clearing a jammed drain pump costs far less than a new control board, and a panel-ready unit takes longer to pull out. Nothing is done until you approve the price, and every repair has a 183-day warranty on parts and labor.

Is It Worth Repairing a Bosch Dishwasher?

In most cases, yes. A drain pump, inlet valve, door springs or heat pump are normal repairs, and Bosch says genuine spare parts stay available for up to 15 years. Panel-ready models add one more reason, since a new dishwasher also means fitting the custom panel again.

Replacing makes more sense when the tub itself leaks, when the control board is no longer made, or when an older dishwasher needs several major parts at once. The technician gives you the repair price first, and the choice is yours. Our repair or replace guide explains how to weigh it.

Which Areas of Los Angeles Do You Cover?

We repair Bosch dishwashers in Los Angeles and nearby cities, including Beverly Hills, West Hollywood, Hollywood, Los Feliz, Silver Lake, Santa Monica, Venice, Culver City, Century City, Westwood, Brentwood, Pacific Palisades, Studio City, Sherman Oaks, Encino, Burbank, Glendale and Pasadena. See the full service area for other neighborhoods.

Bosch Dishwasher Repair FAQ

How much does Bosch dishwasher repair cost in Los Angeles?

The diagnostic visit is $65, and it goes toward the repair if you go ahead. Most Bosch dishwasher repairs in Los Angeles cost $190 to $400, and a control board job $270 to $480. After testing, you get one price before any work starts, and every repair has a 183-day warranty on parts and labor.

What does E15 mean on a Bosch dishwasher, and how do I fix it?

E15 means water has collected in the base and the leak protection has shut the dishwasher down. Bosch says to turn off the water supply and call for service. Tilting the unit to drain the base may clear the code for a short time, but the leak is still there. It usually comes from the drain pump seal, a hose, the inlet valve or the door gasket.

Why won't my Bosch dishwasher drain?

Start with the filter. Twist it out, rinse it and check the pump cover under it, which should click into place. Glass and food often jam the pump there. Then check the drain hose for kinks, the knockout plug on a new disposal and the air gap on the sink. If the water still stays, the drain pump or its wiring needs testing.

What is the difference between E24 and E25 on a Bosch dishwasher?

Both mean water isn't draining. Bosch uses E24 for a blockage in the drain, such as a kinked hose, a disposal plug or a clogged air gap. E25 points to the drain pump itself, which is jammed or has a loose cover. Clean the filter and the pump area for either one, then reset the dishwasher.

How do I reset my Bosch dishwasher?

Hold Reset 4 Sec., or Start on models without that button, for about 4 seconds. The dishwasher drains for about a minute, then press On/Off. To clear a code, Bosch suggests switching the breaker off for 30 seconds. If the same code comes back, a part needs testing.

Why are my dishes still wet after a Bosch cycle?

Bosch dishwashers dry by condensation, without an exposed heating element, so plastics often stay damp. For glasses and plates, raise the rinse aid setting, keep the dispenser full and use Extra Dry or Sanitize. On 500 Series models AutoAir opens the door at the end to let the steam out. If dishes come out cold as well as wet, the heater may have failed.

How do I get rid of white film from hard water in a Bosch dishwasher?

Run a dishwasher descaler, which Bosch recommends every 3 to 6 months, and raise the rinse aid setting. Only Benchmark models in the US have a built-in water softener, which needs the hardness set and dishwasher salt added. If you see E12, scale has built up in the heat pump and a descaler cycle is the first step.

What do E09 and E22 mean on a Bosch dishwasher?

E09 is a fault in the heater of the heat pump. Bosch suggests switching off the breaker for 30 seconds, and if the code comes back, the heat pump needs testing. E22 means the filter, drain or air gap is blocked. Clean the filter, check the pump cover and the drain hose, then reset.

Why won't my Bosch dishwasher start or turn on?

Check the breaker and the outlet, and make sure the door is fully closed. If all the lights flash and it beeps, switch it off, cut the power for at least 2 minutes and turn it back on. E27 means the supply voltage is too low. If nothing lights up with power at the outlet, the door switch, power supply or control board needs testing.

Why does my Bosch dishwasher door fall open?

A hinge spring or its cable has usually broken or come off. Replacing both sides together keeps the door balanced. On panel-ready models the springs are set for the weight of the custom panel, so the technician checks that setting too. A door that won't latch is a separate repair, usually the latch or the door switch.

Is it worth repairing a Bosch dishwasher?

Usually, yes. Pumps, valves, door springs and the heat pump are normal repairs, and Bosch says genuine spare parts stay available for up to 15 years. Replacing makes more sense when the tub leaks, the control board is no longer made or several major parts fail at once on an older unit.

Where is the model number on a Bosch dishwasher?

Bosch puts the rating label inside the door. Open the door and look along its edge. Send us the E-Nr (the model number) and the FD number when you book, so we can check the parts before the visit.

Are you a Bosch authorized service provider?

No. Appliance Insight is an independent repair company and isn't affiliated with Bosch. Bosch covers a new dishwasher for 1 year on parts and labor. Electronic parts are covered for years 2 through 5, parts only. If yours may still be covered, contact Bosch first, because its warranty excludes damage from work by a non-authorized servicer.

Can you come the same day?

Often, yes. Call before 11 AM for the best chance of a same-day visit. If the dishwasher needs a Bosch part that has to be ordered, we come back once it arrives.

Schedule Bosch Dishwasher Repair in Los Angeles

Call (213) 761-5757, 8 AM to 8 PM every day, or book online any time. Call before 11 AM and there's a good chance we can come out the same day. Have the model number (E-Nr) and the FD number from the label inside the door ready, so we bring the right part. For other Bosch appliances see Bosch appliance repair. For other dishwasher brands see Miele dishwasher repair, LG dishwasher repair and our dishwasher repair page, and the service area page has every city we cover.