Samsung Washer Error Codes: What 4C, SC, Sud, U6 and DC Mean

Samsung washers put a code on the display for almost every problem. That's useful, because the code tells you which system to look at. It doesn't always tell you which part failed. A 5C can be a sock in the pump filter or a dead pump, and a DC can be a towel caught in the door or a worn lock.

These are the codes we see most on Samsung washers in Los Angeles, what each one means, what you can check yourself, and when it's time to call. Codes vary a little between models, so check your manual if what you see doesn't match.

Samsung Washer Codes at a Glance

CodeWhat it means
4C, 4E, nFNot filling with water
4C2, 4E2, nF1Hot water coming into the cold inlet
5C, SC, 5E, SE, ndNot draining
Sd, Sud, SUdToo many suds
UE, Ub, U6, UrUnbalanced load
dC, dE, dS, dLDoor or lid not closed and locked
LE, LCLeak detected, or a water level sensor problem
OE, OCToo much water in the tub
3C, 3EMotor fault, or a power problem on some models
tE, tCTemperature sensor
CLChild Lock is on
dnDownloading a software update (Wi-Fi models)

4C: Samsung Washer Not Filling

4C (4E on older models, nF on some newer ones) means the washer isn't getting enough water in the time it expects.

What to check:

  • Both faucets behind the washer are open all the way.
  • The fill hoses aren't kinked or pinched against the wall.
  • The inlet screens where the hoses connect to the washer aren't clogged with sediment. Turn off the water before you unscrew the hoses.
  • The drain hose doesn't go more than about 6 inches into the standpipe. If it's pushed in too far, the washer can siphon water out as fast as it fills, and you get a fill code.
  • Samsung also says to turn off the power for one minute and try again.

If you see 4C2, 4E2 or nF1: the hoses are swapped, and hot water is coming into the cold inlet. Switch them and the code goes away. Nothing is broken.

If the faucets are open, the screens are clean and the code keeps coming back, the water inlet valve is the usual cause. On older Los Angeles buildings, low water pressure from old supply lines can do it too.

SC or 5C: Samsung Washer Not Draining

SC, 5C, 5E, SE and nd all mean the washer can't get the water out in time. SC is how some Samsung displays show 5C.

On a front-loader, start with the pump filter behind the small panel at the bottom front corner. Drain the water through the small emergency hose next to it first, then unscrew the filter and clean it out. Then check that the drain hose isn't kinked and that the house drain isn't slow.

If the filter is clean and the code keeps coming back, the drain pump has usually failed. We cover the full drain checklist and the filter steps on our Samsung washer repair page. If the drum also won't spin, see our guide to a washer not draining or spinning.

Sud or Sd: Too Many Suds

Sud, Sd or SUd means the washer found too much foam in the drum. It stops for a while to let the suds settle, then carries on by itself. The code can flash again at the end of the cycle as a reminder. This is not a fault, and you don't need a technician.

Why it happens:

  • Too much detergent. HE washers need very little, often less than the cap line.
  • Regular detergent instead of HE.
  • A pod plus extra liquid detergent in the same load.
  • Clothes that still had detergent in them from a previous wash.

Run a Rinse + Spin with no detergent to clear the drum, then cut back on detergent. If you see Sud with a small amount of HE detergent and the code won't go away, have the washer checked, since a slow drain can leave foam behind too.

U6, UE, Ub and Ur: Unbalanced Load

U6, UE and Ub all mean the washer couldn't balance the load and stopped before the spin. Ur means it's still trying: it adds water, spreads the load and spins again, so the cycle runs longer.

Open the door, untangle the laundry, spread it around the drum and press Start. Bulky single items, like a comforter or bath mat, are the most common cause. Add a couple of towels so the weight spreads out. Also check that the washer sits level and doesn't rock.

If U6 or UE shows up on normal, mixed loads, the problem is usually worn shock absorbers, suspension rods or bearings. We go through those in the not-spinning section of the Samsung washer repair page.

DC or dE: Door or Lid Error

On most Samsung washers, dC, dE, dS and dL mean the door or lid isn't detected as closed and locked. The washer won't start, or it stops mid-cycle.

What to check:

  • Close the door or lid firmly.
  • Look for clothes caught in the door seal of a front-loader.
  • Make sure nothing is blocking the latch or the strike, and that the latch isn't cracked.
  • Turn the washer off for a few minutes and start again.

On some older Samsung models, dC means an unbalanced load instead of a door problem. If the door is clearly shut and you get dC at the start of the spin, treat it like a U6.

If the door is closed, nothing is in the way and the code keeps coming back, the door lock assembly or its wiring has usually failed. A door lock is a common, one-visit repair on most Samsung washers.

Other Samsung Washer Codes You Might See

  • LE or LC: the washer detected water where it shouldn't be, or the level sensor is acting up. Look for small leaks under the washer and for heavy suds. Run an empty cycle with no detergent and see if it comes back.
  • OE or OC: too much water in the tub. This usually needs a technician, since the level sensor or the fill valve is the likely cause.
  • 3C or 3E: a motor fault. On some models 3E points to the power supply, so make sure the washer is on its own outlet and not on an extension cord.
  • tE or tC: the water temperature sensor. We wrote up a Samsung washer that wouldn't spin because of a temperature sensor error in West Hollywood.
  • CL: Child Lock is on. Turn it off with the button combination on your control panel, usually marked with a lock symbol.
  • dn: a Wi-Fi model is downloading a software update. Wait for it to finish.

How to Reset a Samsung Washer After an Error Code

For most codes, Samsung suggests turning the washer off for 2 to 3 minutes, turning it back on and starting the cycle again. If the same code comes back right away, resetting won't fix it.

Many Samsung washers also have a built-in self-test. On a lot of models you set Delay End to 17 hours and hold Start until AS appears on the display, then press Start again. The washer checks the door lock, the valves, the drain and the spin, and shows OK at the end or the code for the step that failed. Samsung says not to run it while an error code is already showing, so deal with that code first. Button steps differ between models, so check your manual.

When to Call a Technician

Call when the same code keeps coming back after you've done the basic checks, when the washer is leaking onto the floor, or when you hear grinding or loud banging during the spin. Running a washer that keeps throwing the same code can turn a pump or a door lock repair into a bigger one.

We repair Samsung washers at home across Los Angeles. The diagnostic is $65 and goes toward the repair if you go ahead, and completed repairs carry a 183-day warranty on parts and labor. Appliance Insight is an independent repair company, not affiliated with or authorized by Samsung.

Related: Samsung washer repair • Washer repair in Los Angeles • Samsung appliance repair

FAQ

Why does my Samsung washing machine show 4C?

4C means the washer isn't filling fast enough. Check that both faucets are fully open, the hoses aren't kinked, the inlet screens are clean, and the drain hose isn't pushed too far into the standpipe. If all of that is fine, the water inlet valve has usually failed.

Why does my Samsung washer say Sud?

Sud means too many suds. The washer pauses to let the foam settle, then finishes the cycle. Use less HE detergent and run a Rinse + Spin with nothing in it. It isn't a fault.

What does DC mean on a Samsung washer?

On most models DC means the door or lid isn't detected as closed and locked. Close it firmly and check for clothes caught in the seal. On some older models dC means an unbalanced load instead. If the code keeps coming back with the door closed, the door lock usually needs replacing.

Can I clear a Samsung washer error code myself?

Often, yes. Turn the washer off for 2 to 3 minutes, fix the cause (a closed faucet, a clogged filter, a tangled load) and start again. If the same code comes back right away, a part has likely failed and the washer needs a diagnostic.

Give us a call if your washer stops before the spin, shows an error code, leaks around the door, or shakes and bangs on the spin. Keep running a washer that's shaking hard and you can damage the tub, the bearings and the cabinet, so it's worth getting it looked at. Call (213) 761-5757, the diagnostic is $65 and it comes off the bill if you go ahead.