Appliance Insight repairs Electrolux wall ovens, combination wall ovens and range ovens across Los Angeles. The technician tests the oven on the first visit and gives you one price for parts and labor before any work starts. The $65 diagnostic goes toward the repair, and every repair carries a 183-day parts and labor warranty.
We're an independent repair company, not an Electrolux authorized service center. Electrolux ovens come with a one-year limited warranty, so if yours is still covered, check with Electrolux first.
First rule out two settings. If the oven lights up and the display works but nothing gets hot, it may be in Demo Mode. Electrolux's fix is to switch the breaker off, wait 45 seconds, switch it back on, then turn Demo Mode off in the settings menu. The second is Sabbath mode on wall ovens: after a power cut the display shows "SF" and the oven will not restart until Sabbath mode is turned off.
If the settings are fine, these are the usual causes:
Electrolux also points to the door gasket. A torn or loose gasket lets heat out and slows preheat, so look at it, but do not pull or rub it.
Electrolux ovens show faults as an F followed by a number. The table uses Electrolux's owner support guide and its service manual for electric ranges. Code meanings can differ between models, so write down the full code and the model number before you call.
| Code | What it means | What to try first |
|---|---|---|
| F10 | Oven temperature higher than normal (runaway heat) | Turn the oven off and let it cool. If it keeps heating after you press Cancel, switch off the breaker and book a repair. |
| F11 | Shorted keypad | Clean around the touch panel and cut the power for 30 seconds. If it returns, the keypad needs testing. |
| F13 | Internal error in the oven control | Cut the power for 30 seconds. If F13 comes back, book a repair. |
| F14, F15 | Display connection or signal lost between control boards | Cut the power for 30 seconds. A returning code points to a loose connector or a board. |
| F30 | Temperature probe circuit fault | Unplug the oven or switch off the breaker for 30 seconds. If it returns, the sensor or its wiring needs testing. |
| F31 | Door lock motor or latch failure | Do not force the door. Cut the power for 30 seconds, then book a repair if the lock still fails. |
| F90 to F94 | Door lock problem | Press Unlock and follow the steps on the display. If that does not work, cut the power for 30 seconds. |
Electrolux says pressing Cancel clears an F code so you can reprogram the oven. If the same code comes back, a part needs testing. Clearing it again and again does not fix the cause.
On Electrolux wall ovens a self clean cycle runs 2, 3 or 4 hours, depending on the level you pick. The door locks when the cycle starts and stays locked while the display shows "Hot". Electrolux says the door can be opened once the oven has cooled for about an hour and the door icon has gone out. A locked door right after cleaning is normal.
If the oven is cold and the door is still locked, press Unlock and follow the prompts. If that does not release it, cut the power for 30 seconds and try again. Do not pull hard on the handle. Forcing the door can break the latch, the hinges or the glass.
A door that stays locked usually comes down to the door lock motor or its switch, a thermal fuse that opened from the cleaning heat, or a control board that no longer sends the unlock signal. We test each one before replacing anything.
A few degrees of swing is normal, because the oven cycles the element on and off to hold the set temperature. If food is always over or under done, you can adjust the oven. On Electrolux wall ovens the setting is in the User Preferences menu and lets you shift each oven up to 35°F either way. The menu differs between models, so check your owner's manual.
If the oven is off by more than that, or the error changes from day to day, the temperature sensor, a weak element or the gasket is the usual cause, and an adjustment will only hide it.
On some Electrolux wall ovens the fan stays off during Convection Broil while the door is open, which is normal. If the fan does not turn with the door closed, or it grinds or squeals, the fan motor or its bearing is usually worn. A failed convection element gives the same symptom: the fan runs, but the oven stays cool on convection modes.
Wall ovens. Single and double built-in ovens, including the newer ECWS and ECWD models with Air Fry and Air Sous Vide, and older EI30EW and ICON E30EW models. Many repairs are done from the front, without pulling the oven out of the cabinet.
Combination wall ovens. An oven with a microwave above it, such as the ECWM models. The microwave stores high voltage even when it is switched off, so this part is for a technician only.
Range ovens. The oven side of Electrolux gas, electric, induction and dual fuel ranges, freestanding and slide-in: elements, igniters, sensors, convection fans and door locks.
Send us the model number when you book so the technician can check part availability first. Electrolux puts it on the side trim of the oven, visible when the door is open. On some ranges it is on the left side panel or on the frame behind the storage drawer.
If you smell gas, do not switch anything on or off. Leave the house and call SoCalGas or 911 from outside.
The technician starts by watching the oven run and reading any error code. Then the elements, igniter, temperature sensor, thermal fuse, fan motor and door lock are tested with a meter, so a part is replaced only when it is proven bad.
You get one price for parts and labor before any work starts. If a part has to be ordered by model number, we come back once it arrives. Before the technician leaves, the oven is run again and checked to hold its temperature.
Usually, yes. Elements, igniters, sensors, fan motors and door locks are common, clear repairs, and a working oven keeps its cabinet cutout and its matching finish. A new built-in oven of a different size often means cabinet work too.
Replacement makes more sense when an older oven needs a control board that is no longer made, or several parts have failed at once. In that case the technician tells you the price of the part first, so you can decide before anything is ordered.
The diagnostic visit is $65. If you go ahead with the repair, the $65 is credited toward it. If you decide not to repair, you pay only the $65.
The final price depends on the part and how the oven is installed. After the diagnosis you get one price for parts and labor, and nothing is done until you approve it. Every repair has a 183-day warranty on parts and labor.
The diagnostic visit is $65, and it is credited toward the repair if you go ahead. After the diagnosis you get one price for parts and labor before any work starts. Every repair has a 183-day warranty on parts and labor.
No. Appliance Insight is an independent repair company and is not affiliated with Electrolux. Electrolux ovens have a one-year limited warranty, so if yours is still covered, contact Electrolux first.
Unplug the oven or switch off its breaker for 30 seconds, then turn the power back on. Electrolux says this clears most false error codes. If the same code comes back, a part needs testing.
F10 means the oven detected a higher than normal temperature. Turn the oven off and let it cool. If it keeps heating after you press Cancel, switch off the breaker and book a repair, because a stuck relay on the control board can keep the element on.
F30 points to the oven temperature probe circuit. Cut the power for 30 seconds. If F30 returns, the sensor or its wiring needs testing.
F90 to F94 are door lock codes. Press Unlock and follow the steps on the display. If the door stays locked, cut the power for 30 seconds and try again. Do not force the door, because that can break the latch.
On Electrolux wall ovens self clean runs 2, 3 or 4 hours, depending on the level. The door stays locked while the oven is hot and opens once it has cooled for about an hour.
The most common cause is a weak igniter. It can glow but never get hot enough to open the gas valve, so the burner does not light or the oven loses heat. If you smell gas, leave the house and call SoCalGas or 911 from outside.
On Electrolux wall ovens you can shift the temperature up to 35 degrees F either way in the User Preferences menu. The menu differs between models, so check your manual. If the oven is off by more than that, the sensor or an element usually needs testing.
On some wall ovens the fan stays off during Convection Broil while the door is open, which is normal. If it does not turn with the door closed, or it grinds, the fan motor is usually worn.
Usually, yes. Elements, igniters, sensors, fan motors and door locks are common repairs. Replacement makes more sense when an older oven needs a control board that is no longer made, and we tell you the part price before you decide.
Each oven in a double wall oven has its own bake and broil elements, its own temperature sensor and its own relays on the control board. If the top oven heats and the bottom one does not, power and the display are fine, and the fault is in the lower oven's element, sensor or relay. We test the lower oven on its own.
Cut the power for 30 seconds first. If the display stays blank, check the breaker, then the display connection, the keypad and the control board, which F11 and F14 codes also point to. If the oven will not turn off, or it keeps tripping the breaker, leave the breaker off and book a repair, because a shorted element or wire can cause both.
Yes, both the oven and the microwave. Please do not open the microwave housing yourself, because it stores high voltage even when it is switched off.
Often, yes. Call before 11 AM for the best chance of a same-day visit. If a part has to be ordered, we come back once it arrives.