Appliance Insight repairs Miele washers and washing machines across Los Angeles, including W1 front loaders with TwinDos, CapDosing and SteamCare, and washers stacked with a Miele dryer. The technician tests the washer on the first visit and gives you one price for parts and labor before any work starts. The diagnostic is $65 and goes toward the repair, and every repair carries a 183-day parts and labor warranty. Call (213) 761-5757 before 11 AM for the best chance of a same-day visit.
We're an independent repair company, not a Miele authorized service center. Miele's standard warranty on household washing machines is two years on parts and labor, so if yours is newer than that, check with Miele first.
We repair every part of a Miele washing machine, from the drain pump and door lock to the drum drive and the electronics. These are the problems we see most often.
F11, a flashing Drain light and "Water drainage fault" all mean the same thing on a Miele: water can't leave the drum fast enough. Miele lists three things to check first. The end of the drain hose can sit no higher than 3 ft 3 in (1 m), the hose must have no kinks or loops, and the drain filters behind the access panel at the bottom front must be clean. Coins and buttons often jam the pump impeller there.
Put a shallow tray under the panel and open the filters slowly, because the drum can still hold a lot of water, and it can be hot after a hot wash. Screw the filters back in tight, since a loose filter leaks. If the filters are clean and the hose is fine, the drain pump or its wiring needs testing. The general checks that apply to any brand are in our guide to a washer that won't drain.
F10, a flashing Check inlet light and "Water inlet fault" mean water isn't coming in fast enough. Make sure the faucet is fully open and the inlet hose isn't kinked, then clean the small plastic filter at the faucet end of the hose. Miele's test for pressure is simple: with the faucet fully open, about 5 liters should run out within 15 seconds. If the supply is fine and the code returns, the inlet valve or the water control is the usual cause.
A Miele keeps the door locked for normal reasons. It stays locked while a program runs, while the water is above 130°F (55°C), and during anti-crease, when the drum turns now and then for up to 30 minutes after the program ends. A power cut or a tripped breaker also leaves it locked.
F35 means the lock could not release, and F34 means it could not lock, which can happen when the drum is overloaded. For either code, switch the washer off at the plug or breaker, wait at least 2 minutes and switch it back on. Please don't force the door. The emergency release only works safely after the water is drained, and a door lock or latch that fails again needs replacing.
If laundry comes out wet, the washer usually cut the spin speed on purpose. It does that when the load is out of balance, for example one heavy towel or a single bath mat on its own. Mix large and small items and run Spin again. A washer that is not exactly level, or a drain hose higher than 1 m, also stops a good spin. If the drum won't turn at all or the display shows F53, the drum drive has a fault, which Miele lists as a repair for a technician.
Miele's Waterproof system shows this message when it detects water from a leak inside the machine, and F220 also points to a leak. Unplug the washer and look underneath. Water at the front often comes from deposits on the door glass or the door seal, which a damp cloth clears. Water at the back usually means the drain hose sits less than 5 7/8 in (15 cm) inside the standpipe, a loose hose clamp or a leaking supply connection. A leak inside the cabinet, from a hose, the pump or the tub, needs a technician.
Miele notes that F220 sometimes shows when nothing is leaking. If the floor and the base are dry, start any program. If it runs normally, the code was shown in error, and on connected models Miele offers a software update over Wi-Fi for it.
On a new install, check that the transport bars were taken out. Then check that all four feet stand firmly and the counter nuts are tight against the housing. Miele recommends a concrete floor, and on a wood floor a plywood base fixed to the joists. Gurgling while the washer drains is normal. A rubbing or grinding noise as the drum turns is not, and Miele treats it as a technical fault: worn drum bearings, a shock absorber or something trapped between the drum and the tub.
F20 or "Heating fault" can show when the water takes longer than expected to heat. If the code comes back after a 2-minute power reset, the heater or its sensor needs testing. A dark display with power to the outlet points to the main board or its supply. If TwinDos stops dispensing, check that it is switched on in the settings and that the program you chose uses it. If it still can't be used, Miele names a faulty cartridge detection switch in the rear TwinDos compartment as a cause, and that is a repair.
The table uses Miele's own descriptions from its US support library. Depending on the model, the display shows a code such as F11 or the same fault in words, such as "Water drainage fault". Write down the code and the model number before you call.
| Code or message | What Miele says it means | What to try first |
|---|---|---|
| F10, Check inlet, Water inlet fault | Water inlet is blocked or restricted | Open the faucet fully, straighten the hose, clean the inlet filter. |
| F11, Drain light, Water drainage fault | Drain is restricted | Lower the hose end to 1 m or less, remove kinks, clean the drain filters. |
| F16 | Too much foam from detergent or additives | Use less detergent or stain remover and pick a program that suits the load. |
| F20, Heating fault | Set temperature not reached, or a heating fault | Power off for at least 2 minutes, then restart the program. |
| F34 | Door could not be locked | Reduce the load, power off for at least 2 minutes. |
| F35 | Door lock could not release | Power off for at least 2 minutes. If it stays locked, book a repair. |
| F53 | Fault with the drum drive | Not a home fix. Book a repair. |
| F63 | Fault with the water path control unit | Not a home fix. Book a repair. |
| F220 | The washer is leaking, or the code showed in error | Unplug and check for water. If dry, run a program and update the software. |
| Waterproof system activated | Water from an internal leak was detected | Unplug the washer and book a repair. |
Miele's library lists more than 50 F codes, and many change from model to model. If a code returns after you cut the power for 2 minutes, a part needs testing.
W1 front-loading washers. Current and older W1 models such as the WXR860, WWH860, WXI860, WXD160, WXR960, WXC280 and WXF980, including the honeycomb drum, TwinDos automatic dispensing, CapDosing and SteamCare.
Stacked and side-by-side laundry. Miele washers stacked with a T1 dryer or installed side by side. For the dryer, see our dryer repair page.
Older Miele washing machines. Earlier front loaders that show short F codes on a time display. We check which parts are still available by model number before the visit.
Send us the model number when you book so the technician can check parts first. On a Miele front loader the data plate sits above the door glass, and you can see it when the door is open.
The technician starts by reading the fault code and asking what happened, then runs the washer to see the fault. Testing follows the order the problem points to: the water supply and the drain path first, then the door lock, pump, heater, drum drive and sensors, and the electronics last. A part is replaced only when it tests bad.
You get one price for parts and labor before any work starts. Miele parts that have to be ordered by model and serial number mean a second visit. Before the technician leaves, the washer runs a fill, drain and spin to check the repair.
The diagnostic visit is $65. If you go ahead with the repair, the $65 is credited toward it. If you decide not to repair, you pay only the $65.
The final price depends on the part and on how the washer is installed, for example stacked under a dryer or built in. After the diagnosis you get one price for parts and labor, and nothing is done until you approve it. Every repair has a 183-day warranty on parts and labor.
In most cases, yes. Miele tested its W1 front loaders in endurance runs of 5,000 wash cycles, which it equates to five loads a week for 20 years, though it says this is not a guarantee for any single machine. A failed drain pump, door lock, inlet valve, heater or shock absorber is usually a clear repair on a washer built for that kind of use.
Replacement makes more sense when the drum bearings or the tub have failed on an older model, when an electronic board is no longer made, or when several parts have failed at once. In those cases the technician gives you the price of the part before you decide.
We repair Miele washing machines in Los Angeles and nearby cities, including Beverly Hills, West Hollywood, Hollywood, Los Feliz, Santa Monica, Venice, Marina del Rey, Culver City, Century City, Westwood, Brentwood, Pacific Palisades, Studio City, Sherman Oaks, Encino, Pasadena, South Pasadena and San Marino. See the full service area for other neighborhoods.
No. Appliance Insight is an independent repair company and is not affiliated with Miele. Miele's standard warranty on household washing machines is two years on parts and labor, so if your washer is still covered, contact Miele first.
The diagnostic visit is $65, and it is credited to the repair if you go ahead. After testing, the technician gives you one price for parts and labor before any work starts. Every repair has a 183-day parts and labor warranty.
Switch the washer off, then unplug it or turn off its breaker. Wait at least 2 minutes, reconnect the power and switch it on. This is the step Miele gives for many faults. If the same code comes back, a part needs testing.
Check that the end of the drain hose is no higher than 3 ft 3 in (1 m) and that the hose has no kinks. Then clean the drain filters behind the access panel at the bottom front, with a tray underneath for the water. If the filters are clear and it still won't drain, the drain pump needs testing.
Most often the load is out of balance, so the washer lowers the spin speed to protect itself. Mix large and small items and run Spin again, and make sure the washer stands level. If the drum doesn't turn at all or the display shows F53, the drum drive needs a repair.
Don't force it. The door stays locked during a program, while the water is above 130°F (55°C) and during anti-crease, which can last up to 30 minutes after the program ends. If it stays locked, switch the washer off for at least 2 minutes. If it still won't open, the drum has to be drained before the emergency release is used, and a lock that keeps failing needs replacing.
Waterproof system activated means the washer detected water from a leak inside the machine. Unplug it and book a repair. Check inlet means water isn't coming in fast enough: open the faucet fully, straighten the hose and clean the small filter at the faucet end of the inlet hose.
Miele lists F53 as a fault with the drum drive and F63 as a fault with the water path control unit. Neither is a home fix. F220 means the washer is leaking, but Miele notes it can also show in error, so check for water first.
Check that TwinDos is switched on in the settings, that the cartridges are in place and that the program you chose uses TwinDos. Some programs don't, and you add detergent through the drawer instead. If TwinDos still can't be used, the cartridge detection switch may be faulty, and that is a repair.
Usually, yes. Miele tested its W1 front loaders for 5,000 wash cycles, which it compares to five loads a week for 20 years, while noting this is not a guarantee. Pumps, door locks, valves and shock absorbers are common repairs. Bearing or tub failure on an older model is the case where replacing can make more sense.
Often, yes. Call before 11 AM for the best chance of a same-day visit. If the washer needs a part that has to be ordered, we come back once it arrives.