Appliance Insight repairs LG refrigerators in Los Angeles: a warm fresh-food section, an ice maker that froze up, an Er code on the display or a refrigerator that runs but doesn't cool. The diagnostic is $65 and goes toward the repair, you get one price before any work starts, and every repair has a 183-day parts and labor warranty. Call (213) 761-5757 before 11 AM for the best chance of a same-day visit.
We're an independent repair company, not an LG authorized service center. LG covers a new refrigerator for one year, the sealed system for five years, and on models with a linear or inverter compressor the compressor part for ten years. If yours may still be covered, contact LG first.
We work on LG refrigerators of every style sold in the US, built-in looking models included.
The model and serial number are on a label inside the refrigerator. On newer LG models it is on the left wall of the fresh-food section, on most older models on the right wall, and on some models it is on the back. The LG ThinQ app also shows them if the refrigerator is connected. A photo of the label helps us bring the right part on the first visit. If the first three digits of the serial number are 901 or higher, the refrigerator was made in 2019 or later.
We repair the whole refrigerator: ice makers, fans, defrost heaters and sensors, water valves and dispensers, door seals, control and inverter boards, and the sealed system with the linear compressor. These are the problems we see most often on LG refrigerators in Los Angeles homes.
If the lights are on, the display works and the refrigerator is warm, start with the simple causes. LG lists a control set to off, Demo Mode, a defrost cycle in progress, a refrigerator that was just installed and blocked vents as normal reasons for no cooling. After setup or a power outage, LG says it can take up to 24 hours to reach temperature. On current models the factory settings are 37°F for the fridge and 0°F for the freezer.
If none of that applies, the cause is usually airflow, defrost or the compressor. When both sections are warm, we test the condenser fan, the inverter board and the linear compressor. LG reports a refrigerant leak on the high or low pressure side with the codes CH and CL, which points to the sealed system. A compressor that runs only part of the time is normal: LG says 40 to 80 percent of the time at 70°F.
On most LG refrigerators the cold air for the fresh-food section comes from the freezer. When the fridge goes warm and the freezer stays cold, the evaporator fan in the freezer has stopped or the coil behind the freezer panel is packed with frost, and air can't get through. A solid wall of frost behind that panel means defrost isn't working: the defrost heater, the defrost sensor or the board that runs them. LG shows this as the code dH when the temperature doesn't rise enough during defrost. Check that food isn't blocking the vents inside the fridge first, because that alone can make it run warm.
This is the classic LG French door problem. Ice builds up inside the ice compartment in the upper left door, the bucket freezes in place and the auger can't turn, so the dispenser stops or the cubes fuse into one lump. Chipping it out works for a while, but the ice comes back while the cause is still there. Usually that is the ice compartment seal, the ice fan or a heater, and that's what we test and fix. If the display shows Er IF, LG reports a problem with the ice maker fan, often blocked by ice.
First make sure the ice maker is on. On many models the ice button needs a 3-second hold, and if the panel is locked, hold Lock for 3 seconds first. A new ice maker takes time: LG says the first ice takes 12 hours to 2 days, and the in-door ice maker makes ice faster than the one in the freezer. Throw away the first bin. If the water filter is older than about 6 months, replace it and run about 2.5 gallons through the dispenser. You can also set the freezer 1 or 2 degrees colder and watch it for 24 hours.
Most LG ice makers have a test button. Holding it for 3 seconds makes the ice maker run a cycle. If the tray doesn't turn or no water comes in, the ice maker, the water valve or the water supply needs to be checked. LG's current French door manual asks for at least 20 psi of water pressure, and 40 psi on models with a filter. Low pressure is common with reverse osmosis systems. The code It points to the ice maker motor and IS to the ice maker sensor.
Check that the supply valve behind the refrigerator is fully open and the hose isn't kinked, then replace an old filter. If the line in the door froze, LG suggests setting the fridge 1 or 2 degrees warmer. The code gF means the water flow sensor isn't seeing water. If the dispenser still doesn't work, we test the water valve, the dispenser switch and the heater in the door.
Water under the crisper drawers usually means a frozen or clogged defrost drain. A puddle in front or under the refrigerator usually comes from the water supply. LG's checks are a water line that isn't pushed all the way in (when it is, you can no longer see the two marks on the tube), a cracked line, air in the lines, a stuck dispenser lever and a filter that isn't seated or isn't made for the refrigerator. If a water line is damaged, close the supply valve until it is fixed.
LG lists hissing or sizzling during defrost, gurgling from refrigerant, cracking or clicking from plastic parts and a hum or rattle when the compressor or fans start as normal sounds. A scraping or chattering that stops when you open the door is not normal. It is usually a fan hitting ice, in the freezer or in the ice compartment, and the ice will come back until the cause is fixed. A compressor that clicks on and off without starting needs a test of the inverter board and the compressor.
Depending on the model, LG shows a code as Er FF, E FF or just FF. These are the codes from LG's own list that we see most often. After a power outage, you can bring a stored code back on many models by holding Freezer Temp and Express Frz together for 3 seconds.
| On the display | What LG says it means | What to do |
|---|---|---|
| Er FF, E FF | Freezer fan, usually blocked by ice | Unplug and leave the doors open at least 24 hours (up to 3 days in winter), no hair dryer. If it comes back, call for service |
| Er IF, E IF | Ice maker fan, often blocked by ice | Service; the ice in the compartment has a cause |
| Er CF | Condenser fan near the compressor | Service |
| Er dH | Defrost not working | Service; LG suggests unplugging with the doors open for at least 12 hours in the meantime |
| Er CO, E CO | Main board and display not communicating | Unplug or switch off the breaker for about 5 minutes. If it returns, a board or wire needs service |
| Er rS, Er FS | Fridge or freezer temperature sensor | Service |
| Er dS | Defrost sensor | Service |
| Er rF | Fridge fan | Service |
| Er It, Er IS | Ice maker motor, ice maker sensor | Service |
| Er gF | Water flow sensor | Unplug for 60 seconds, then check the water valve, the hose and the pressure |
| CH, CL | Refrigerant leak, high or low pressure side | Sealed system service |
| O F F | Demo Mode, cooling is off | Turn Demo Mode off, see the checks below |
A code tells us where to start, not which part to buy. A fan code can come from the fan, the ice around it, its wiring or the board, so we test before replacing anything.
Some LG refrigerator problems take five minutes to sort out yourself. We'd rather you didn't pay for a visit you don't need.
If a fan code keeps coming back, the doors are frozen shut, the refrigerator is warm after 24 hours or there is water coming from the back, it's time for a diagnosis.
The technician starts with what you saw: which section is warm, when the ice stopped, any code on the display and whether it started after a power outage. Then we measure the temperature in both sections, open the panel behind the freezer or the ice compartment and look at the frost pattern, because it shows whether the problem is airflow, defrost or the sealed system. Fans are checked for power and for spinning, sensors get a resistance test, the defrost heater and its circuit are tested, and the main board is checked last, after the wiring and connectors. A loose plug can look exactly like a dead board.
When the compressor won't run, we test the inverter board and the linear compressor separately before saying anything. A board costs far less than a sealed system repair. If the evaporator is packed with ice, it has to melt completely first, and the technician tells you how long that takes. You get one price for parts and labor before any work starts. If a part has to be ordered by model and serial number, we tell you when it should arrive and come back to finish. Before we leave, both sections are checked for airflow and the ice maker runs a test cycle.
The diagnostic visit is $65. If you go ahead with the repair, the $65 is credited toward it. If you decide not to repair, you pay only the $65.
The final price depends on the failed part and the model. A fan motor, a sensor, a water valve or an ice maker costs much less than a compressor or sealed system repair, and an InstaView or Signature refrigerator takes more work to get into than a top freezer model. That is why we don't quote over the phone. After the diagnosis you get one price for parts and labor, and nothing is done until you approve it. Every repair has a 183-day warranty on parts and labor.
In most cases, yes. The failures we see most on LG refrigerators are an iced-up ice compartment or evaporator, a fan, a defrost part, a sensor or a water valve. These are normal repairs and cost far less than a new French door refrigerator.
A compressor failure is the bigger decision. Before you decide, check your LG warranty: on models with a linear or inverter compressor, LG covers the compressor part for 10 years and labor for the first 5. Replacement makes more sense when the sealed system fails on an older refrigerator with no coverage left, when the board for an older model is no longer made, or when several major parts fail at once. The technician gives you the repair price after the diagnostic, so you can compare it with a new refrigerator before you pay for anything more.
We repair LG refrigerators in Los Angeles and nearby cities, including West Hollywood, Beverly Hills, Hollywood, Silver Lake, Los Feliz, Echo Park, Santa Monica, Culver City, West Los Angeles, Westwood, Brentwood, Venice, Marina del Rey, Sherman Oaks, Studio City, Encino, North Hollywood, Burbank, Glendale and Pasadena. See the full service area for other neighborhoods.
The diagnostic visit is $65, and it is credited to the repair if you go ahead. The final price depends on the part and the model: a fan, sensor, water valve or ice maker costs much less than a compressor or sealed system repair. After testing, the technician gives you one price for parts and labor before any work starts, and every repair has a 183-day warranty.
First rule out the simple causes LG lists: the control set to off, Demo Mode (O F F on the display), a defrost cycle, a new installation and blocked vents. After setup or a power outage, LG says it can take up to 24 hours to cool down. If it's still warm after that, the usual causes are a stopped evaporator or condenser fan, a failed defrost system, the inverter board or the linear compressor. The codes CH and CL point to a refrigerant leak.
Usually the cold air from the freezer isn't getting to the fridge side. The evaporator fan may have stopped, or the coil behind the freezer panel is iced over because defrost failed. Check that nothing is blocking the vents inside first. If it's still warm after a day, it needs a diagnosis.
Check that the ice maker is turned on (on many models the button needs a 3-second hold), that the water supply valve is open and that the filter is less than about 6 months old. A new ice maker can take 12 hours to 2 days to make its first ice. Hold the ice maker test button for 3 seconds: if the tray doesn't turn or no water comes in, the ice maker, the water valve or the supply needs service. You can also set the freezer 1 or 2 degrees colder and watch it for 24 hours.
On many French door models ice builds up inside the ice compartment in the upper left door until the bucket and the auger freeze in place. Melting it out helps for a while, but the ice comes back until the cause is fixed, usually a worn compartment seal, an ice fan problem or a failed heater. If the display shows Er IF, LG reports a problem with the ice maker fan.
LG says FF points to the freezer fan, usually because ice has built up around it. LG's steps are to unplug the refrigerator and leave the doors open for at least 24 hours, up to 3 days in winter, without using a hair dryer, then give it 24 to 48 hours to cool down. If the code comes back, the defrost system or the fan needs service, because the ice will keep returning.
There is no general reset button. Unplug the refrigerator or switch off its breaker for about 5 minutes, then power it back on, and give it up to 24 hours to reach temperature. The ice maker has its own test button, held for 3 seconds. A reset can clear a communication code such as Er CO or a frozen display. It won't fix a fan blocked by ice, a failed sensor or a leak.
Signs include both sections going warm while the lights and display work, a compressor that clicks without starting, or one that runs all the time without cooling. The same symptoms can come from the inverter board or the condenser fan, so we test those first. On models with a linear or inverter compressor, LG covers the compressor part for 10 years and labor for the first 5, with the sealed system covered for 5 years. Check your own warranty card, since terms vary by model and purchase date.
Check the supply valve, look for a kinked hose and replace a filter older than about 6 months. If the line in the door froze, LG suggests setting the fridge 1 or 2 degrees warmer. The code gF means the flow sensor isn't seeing water. If it still won't dispense, we test the water valve, the dispenser switch and the door heater.
Water under the crisper drawers is usually a frozen or clogged defrost drain. Water on the floor usually comes from the supply: a water line not pushed in all the way, a cracked line, air in the lines, a stuck dispenser lever or a filter that isn't seated. If a water line is damaged, close the supply valve until it's repaired.
LG lists hissing during defrost, gurgling, clicking from plastic parts and a hum or rattle when the compressor or fans start as normal. A scraping or chattering sound that stops when you open the door is usually a fan hitting ice and needs a repair, because the ice keeps coming back until the cause is fixed.
LG doesn't publish a lifespan, and it depends on use and on how well the defrost and ice systems have been kept working. Fans, defrost parts, sensors, water valves and ice makers are normal repairs that cost far less than a new refrigerator. Replacement makes more sense when the sealed system fails after LG's coverage ends, or when an older board is no longer made.
No, we're independent and not affiliated with LG. If your refrigerator is still under LG's factory warranty, contact LG first. Out of warranty, we order parts by your model and serial number and cover the repair for 183 days on parts and labor.