Whirlpool Washer Repair in Los Angeles

Appliance Insight repairs Whirlpool washers and washing machines across Los Angeles: top-load washers with an agitator, the 2 in 1 Removable Agitator or an impeller, front-load washers, and stacked laundry centers in closets and garages. The technician tests the washer on the first visit and gives you one price for parts and labor before any work starts. The diagnostic is $65 and goes toward the repair, and every repair carries a 183-day parts and labor warranty. Call (213) 761-5757 before 11 AM for the best chance of a same-day visit.

  • $65 diagnostic, credited to the repair
  • 183-day warranty on parts and labor
  • One price before any work starts
  • Phones 8 AM to 8 PM every day, online booking 24/7
  • Licensed & insured, CA license A 50129, BBB Accredited

We're an independent repair company, not a Whirlpool authorized service provider. Whirlpool's standard limited warranty on washers covers parts and labor for one year from purchase, so if yours is newer than that, contact Whirlpool first.

Technician testing the lid lock wiring of a top-load washer in a Los Angeles laundry room

On This Page

What Whirlpool Washer Problems Do You Fix?

We repair top-load and front-load Whirlpool washing machines, from the drain pump and lid lock to the motor, the water valves and the control board. These are the problems we see most often in Los Angeles homes.

Whirlpool washer not draining

Water left in the tub, or F9 E1 or drn on the display, means the washer could not pump the water out in time. On a front loader, Whirlpool sets that limit at about 8 minutes. Start with the drain hose. It should have no kinks, sit no more than 5 in inside the standpipe on a top loader (4.5 in on a front loader), and never be taped in place, because a hose pushed in too far or sealed airtight can siphon water back out of the washer. Whirlpool also limits the drain height to 96 in (8 ft).

Too much detergent stops the pump as well, so a Sud or F0 E2 code often shows up together with a drain problem. Some front-load models have a drain pump filter you can open and clean, and the owner's manual shows where it is. Have a shallow tray and towels ready. Most top loaders have no filter you can reach, and a clogged or failed drain pump there is a job for a technician. Our guide to a washer not draining or spinning walks through each check step by step.

Whirlpool washing machine not spinning

Wet clothes at the end of a cycle usually mean the washer slowed the spin on purpose. It does that when the load is out of balance (F0 E5 or Ofb), too large (OL), or full of suds. A single heavy item such as a bath mat or a comforter is the classic cause. Rearrange the load, add a towel or two to balance one bulky piece, and run Drain & Spin or Rinse & Spin. The lid or door has to be closed and locked for the washer to spin at all.

If the drum still won't turn, or you hear the motor hum while the basket stays still, the cause is usually mechanical. On top loaders we most often find a worn drive coupling or shifter, a failed lid lock or a motor fault. On front loaders it is more often the drive belt, the motor or its speed sensor, which Whirlpool reports as F7 E1.

Lid locked, door won't open or the Lid Lock light is flashing

A Whirlpool keeps the lid locked until the basket has stopped, and that can take several minutes after the spin. On many top loaders, holding Start for 3 seconds pauses the cycle and unlocks the lid. A front loader stays locked while the water is high or hot or the drum is moving. Press Pause/Cancel twice and wait up to 5 minutes for the lock to click open.

A flashing Lid Lock light, LdL, F5 E1 or F5 E2 means the lock could not close. Look for clothing or a towel caught in the lid, then check the striker on the lid and the lock opening for detergent buildup or lint. LdU means the lid could not unlock, often because something is sitting on top of it. If a 5-minute power reset does not clear F5 E3 or the code keeps coming back, the lid lock assembly or its wiring needs testing. Please don't force the lid. A broken latch turns a lock repair into a lid repair.

Not filling, filling slowly or showing LF

LF, Lo FL and F8 E1 all mean the washer is taking too long to fill. Both faucets behind the washer have to be fully open and both hoses connected, even if you wash in cold water. Turn off the water, unscrew the hoses and clean the small screens at the inlet with an old toothbrush. Whirlpool also advises against anti-flood devices on the hoses, because they can cut the flow. HC means the hot and cold hoses are reversed. If the supply is good and the code returns, the inlet valve or the water level sensor is the usual cause, and F3 E1 points to the level sensor or its wiring.

Whirlpool washer leaking from the bottom

Unplug the washer and find where the water starts. Water at the back often comes from a loose hose connection, a worn hose washer or a drain hose that slipped out of the standpipe. Whirlpool recommends replacing fill hoses every 5 years. Water under the front of a front loader often comes from the door seal, the dispenser or too many suds pushing water out. Water from under the cabinet, from the pump, a tub seal or an internal hose, needs a technician.

Shaking, walking or banging on the spin

On a new front loader, check that the shipping bolts were taken out of the back. Whirlpool warns that leaving them in causes vibration and noise and can damage the washer. Then check that all four feet stand firmly on the floor and that the load is balanced. If a top loader keeps banging after that, the suspension is usually worn. We wrote up one such repair in Whirlpool washer shaking and bouncing: worn shock absorbers.

Won't start, stops mid-cycle or smells

If no button responds, check whether Control Lock is on (a padlock icon, or LOC on the display) and that the breaker hasn't tripped. PF means the power went out during a cycle, and Int on a front loader means the cycle was paused or cancelled. A washer that stops at random, resets itself or shows codes Whirlpool lists only as "call for service", such as F1 E1 or F6 E1, needs the control board and wiring tested. For odors, Whirlpool recommends the Clean Washer cycle with an affresh tablet or liquid chlorine bleach once a month or every 30 cycles, and leaving the lid or door open between loads.

What Do Whirlpool Washer Error Codes Mean?

The meanings below come from Whirlpool's own product help pages. The same code can mean something slightly different on a top loader and a front loader, so the tables are split. Write down the code and the model number before you call.

Top-load Whirlpool washer codes

CodeWhat Whirlpool says it meansWhat to try first
F9 E1, drnLong drain, the washer is not draining properlyStraighten the hose, keep it no more than 5 in inside the standpipe, don't tape it.
LF, Lo FL, F8 E1Taking too long to fillOpen both faucets fully, clean the inlet screens.
LdL, F5 E1, F5 E2Lid not closed or the lid lock can't engageClear anything under the lid, clean detergent from the lock area.
LdULid can't unlockRemove anything sitting on the lid.
F5 E3Lid lock errorUnplug for 5 minutes. If it returns, book a repair.
F0 E5, Ofb, OLLoad out of balance or too largeRearrange or remove items, run Drain & Spin.
F0 E2, SudToo many sudsUse less HE detergent, run a rinse.
F3 E1Water level can't be detectedUnplug for 5 minutes. If it returns, book a repair.
HCHot and cold hoses reversedSwap the hoses at the washer.
PFPower failure during the cycleCheck the outlet and breaker, then restart the cycle.

Front-load Whirlpool washer codes

CodeWhat Whirlpool says it meansWhat to try first
F9 E1Draining is taking longer than expected, about 8 minutesCheck the hose for kinks, clean the drain pump filter if your model has one.
F21, F02Draining is taking longer than expected (older front loaders such as Duet)Press Pause/Cancel, check the hose for kinks and use HE detergent.
F8 E1, LO FLLow water flowOpen both faucets fully, check the hoses, remove anti-flood devices.
F5 E1, F5 E2Door switch fault or door not lockingClear clothing from the door, press Pause/Cancel twice and then Power.
F7 E1Motor speed sensing errorCheck that the shipping bolts are out and the drum isn't overloaded.
F0 E5Load off balance, spin speed reducedBalance the load, run Drain & Spin.
Sud, Sd (can look like 5d)Too many sudsUse HE detergent and less of it.
F8 E2Problem with the dispenser systemUnplug for 5 minutes. If it returns, book a repair.
rL, F0 E1, F34Load in the drum when Clean Washer startedTake out the load and restart Clean Washer.
LOC, LCControl Lock is onTurn off Control Lock as shown in your manual.
F1 E1, F6 E1Not explained by Whirlpool, listed as a service codeUnplug for 5 minutes. If it returns, book a repair.

For any other F code, Whirlpool's first step is to unplug the washer for 5 minutes. If the same code comes back after that, a part needs testing.

Whirlpool Top-Load and Front-Load Washers We Repair

Top-load washers. Agitator washers, models with the 2 in 1 Removable Agitator such as the WTW5057LW, WTW6157PB and WTW8127LC, and impeller washers such as the WTW5100HW with the Pretreat Station. We also repair older high-efficiency top loaders sold as Cabrio.

Front-load washers. Current models such as the WFW5720RW with FreshFlow Vent and the WFW6720RR with the Load & Go dispenser, and older front loaders sold as Duet.

Stacked and compact laundry. Stacked laundry centers such as the WET4027HW, washer and dryer towers, and washers stacked under a Whirlpool dryer in a closet. For the dryer side, see our dryer repair page.

Send us the model number when you book so the technician can check parts first. Whirlpool puts the model and serial tag under the lid on the rim of the tub on a top loader, and on the rim of the door opening on a front loader. On a stacked laundry center, look inside the dryer door.

Things to Check Before You Call

  • Check the breaker and the plug, then unplug the washer for 5 minutes and plug it back in. Whirlpool gives this reset for most F codes.
  • Look for a padlock icon or LOC on the display. If Control Lock is on, the buttons won't respond.
  • Make sure both faucets are fully open and neither hose is kinked.
  • Check that the drain hose isn't kinked, taped or pushed more than about 5 in into the standpipe.
  • Rebalance the load and run Drain & Spin if the clothes come out soaked.
  • Use HE detergent and measure it. Too many suds can stop both the drain and the spin.
  • Write down the code, the full model number and what the washer was doing when it stopped.

How We Repair Whirlpool Washers

The technician starts by reading the code and asking what happened, then runs the washer to see the fault. If the model has a service test mode, we use it to run the pump, valves, lock and motor one at a time. Testing follows the order the problem points to: water supply and drain path first, then the lid or door lock, pump, valves, motor and sensors, and the control board last. A part is replaced only when it tests bad.

You get one price for parts and labor before any work starts. Common Whirlpool parts such as lid locks and drain pumps are usually easy to get. If a part has to be ordered for your model, we tell you how long it will take and schedule the repair for when it arrives. Before the technician leaves, the washer runs a fill, drain and spin to check the repair.

How Much Does Whirlpool Washer Repair Cost in Los Angeles?

The diagnostic visit is $65. If you go ahead with the repair, the $65 is credited toward it. If you decide not to repair, you pay only the $65.

The final price depends on the failed part, the model and how the washer is installed, for example a stacked laundry center in a tight closet. That is why we don't quote over the phone. After the diagnosis you get one price for parts and labor, and nothing is done until you approve it. Every repair has a 183-day warranty on parts and labor.

Is It Worth Repairing a Whirlpool Washer?

Usually, yes. Whirlpool washers are among the easier machines to repair: parts are widely available, and many designs change little from year to year. A lid lock, drain pump, inlet valve, drive coupling or set of shock absorbers is a normal repair and usually costs far less than a new washer.

Replacement makes more sense when the tub bearings, the transmission or the motor fails on an older washer, or when several parts have failed at once. In those cases the technician gives you the price of the repair after the diagnostic, so you can compare it with a new washer before you pay for anything more.

Which Areas of Los Angeles Do You Cover?

We repair Whirlpool washing machines in Los Angeles and nearby cities, including West Hollywood, Beverly Hills, Hollywood, Silver Lake, Los Feliz, Echo Park, Santa Monica, Culver City, West Los Angeles, Westwood, Brentwood, Venice, Sherman Oaks, Studio City, Encino, Burbank, Glendale and Pasadena. See the full service area for other neighborhoods.

Whirlpool Washer Repair FAQ

Are you a Whirlpool authorized service provider?

No. Appliance Insight is an independent repair company and is not affiliated with or authorized by Whirlpool. Whirlpool's standard limited warranty on washers covers parts and labor for one year from purchase, so if your washer is still covered, contact Whirlpool first.

How much does Whirlpool washer repair cost in Los Angeles?

The diagnostic visit is $65, and it is credited to the repair if you go ahead. After testing, the technician gives you one price for parts and labor before any work starts. Every repair has a 183-day parts and labor warranty.

Is it worth repairing a Whirlpool washer, or should I replace it?

In most cases a repair is worth it. Lid locks, drain pumps, inlet valves, couplings and shock absorbers are common parts and cost far less than a new washer. Replacement makes more sense when the tub bearings, transmission or motor fail on an older washer, and the technician tells you the repair price first so you can compare.

Why is my Whirlpool washer not spinning?

Most often the load is out of balance or too large, or there are too many suds, so the washer slows the spin to protect itself. Rearrange the load, use less HE detergent and run Drain & Spin with the lid closed. If the motor hums but the basket doesn't turn, a coupling, belt, lid lock or motor part needs testing.

Why won't my Whirlpool washer drain?

Check the drain hose for kinks and make sure it isn't taped or pushed more than about 5 in into the standpipe. On a front loader with a drain pump filter, clean the filter. If the hose is clear and the washer still shows F9 E1 or drn, the drain pump or a blockage inside needs a technician.

Why is the Lid Lock light flashing on my Whirlpool washer, and how do I unlock it?

A flashing Lid Lock light means the lid could not lock, usually because something is caught under the lid or detergent and lint are built up around the lock. To open a locked top loader, wait for the basket to stop and hold Start for 3 seconds. On a front loader, press Pause/Cancel twice and wait up to 5 minutes. Don't force the lid or door.

What do F9 E1, F21, F5 E2, LF, Sd and LOC mean on a Whirlpool washer?

F9 E1 is a long drain, and F21 (or F02) means the same on older front loaders. F5 E2 means the lid or door lock can't engage, and LF means the washer is taking too long to fill. Sd or Sud, which can look like 5d on the display, means too many suds, and LOC means Control Lock is on. See the code tables above for more codes and what to try first.

How do I reset my Whirlpool washer, and when does a reset not help?

Unplug the washer, or turn off its breaker if it is hard-wired, for 5 minutes and then restore power. Many front loaders also clear a code with Pause/Cancel twice and then Power. If the same code returns after a reset, or the washer won't respond at all with Control Lock off, a part has failed and needs testing.

Does a Whirlpool washer need to be calibrated?

Many Whirlpool top loaders have a calibration cycle in service mode. Whirlpool's service sheets call for it after the main control, motor, basket, drive or suspension is replaced, and when the washer overfills, picks the wrong water level or tangles loads. It runs with the basket empty and the lid closed, takes about 2 to 4 minutes and must not be interrupted. The steps differ by model and are not in the owner's manual, so our technician runs it as part of those repairs.

Why does my Whirlpool washer stop mid-cycle or not start?

Check for Control Lock, a lid that isn't fully closed and a tripped breaker first. A front loader shows Int when a cycle was paused or cancelled, and PF means the power went out. A washer that stops at random or resets itself usually has a lid lock, wiring or control board fault.

Why is my Whirlpool washer leaking from the bottom?

Look first at the hose connections and the drain hose at the back. Whirlpool recommends replacing fill hoses every 5 years. On a front loader, check the door seal and use less detergent, since excess suds can push water out. Water from under the cabinet usually means the pump, a tub seal or an internal hose, which needs a technician.

How long do Whirlpool washers last?

Whirlpool doesn't publish a set lifespan, and it depends on how often the washer runs, the loads and how it was installed. What wears out first is usually a part we can replace, such as a lid lock, pump, coupling or shock absorbers. When a major part fails on an older washer, we give you the repair price so you can decide.

Schedule Whirlpool Washer Repair in Los Angeles

Call (213) 761-5757, 8 AM to 8 PM every day, or book online any time. Call before 11 AM and there's a good chance we can come out the same day. Have the model number ready, and send a photo of the model and serial tag (under the lid on a top loader, around the door opening on a front loader) or the code on the display if you can, so we bring the right part. For other Whirlpool appliances see Whirlpool appliance repair. For other washer brands see our washer repair page, and the service area page has every city we cover.